Jump to content
SAU Community

Recommended Posts

So I'm doing an RB26 conversion on my S13. I have spent all my money on the engine setup and don't want to spend money on an R33 gearbox when I have 2x r32 GTR boxes sitting here already.

I've removed the transfer case already and all the internals that seem associated with it. What do I do in terms of the oil pump in the rear?

Any info from someone that has done this would be much appreciated.

cheers,

Greg

i guess u cud bin bits and stuff around with removing the transfercase to save weight.

but just remove the front drive shaft between the transfer case nd front diff, nd u mite need a custom tailshaft/ use da gtr one if its da same length as the s13 driveshaft

All the inners that are associated with the transfer case have already been removed and the transfer case has been cut off as it probably wouldn't fit in the S13 tunnel with it still attached.

  • 4 weeks later...
  • 2 weeks later...

I have done it in my GTR, car is running 630rwhp and loving it.

I welded up the hole left by cutting off the tranfere case with 10mm ally plate then surfaced the gearbox and the tranfere case to be a perfect fit. I then put a litre of diff oil in the tranfere case which with acceleration and decelleration should keep the bearing oiled, they are not noisy yet and that included a thrashing all weekend at powercruise.

One thing to watch out for is make sure tou put the selector pivot back on the selector shaft the right way up, otherwise you will be pulling it apart to do it later, its simple mistake if your not paying attention. ie I did it on mine at around 2am when I should have been in bed instead of working on cars haha.

The oil pump is only there to clamp the wet clutch for the 4WD system. So the short answer is bin it.

incorrect you need it to lube the rear bearings. I have done about 6 of these now greg if you need one done. i just did one for type M in dandy.

this is one of many threads ive posted pics.

http://www.skylinesaustralia.com/forums/Rb...amp;hl=transfer

incorrect you need it to lube the rear bearings. I have done about 6 of these now greg if you need one done. i just did one for type M in dandy.

this is one of many threads ive posted pics.

http://www.skylinesaustralia.com/forums/Rb...amp;hl=transfer

What's your number Trent?

I also need the motor built and I'm over waiting around for people.

incorrect you need it to lube the rear bearings. I have done about 6 of these now greg if you need one done. i just did one for type M in dandy.

this is one of many threads ive posted pics.

http://www.skylinesaustralia.com/forums/Rb...amp;hl=transfer

Sorry my bad.

I assumed you were referring to the ATTESSA pump that plugs intot he back of the gearbox/transfer case.

The internal oil pump inside the gearbox should be kept.

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yucky. Things haven't gotten any better though. Now you have Emerson and Honeywell pushing these massive DCS/Scada things with proprietary hardware. They're not a PLC, they're not a computer, they're a...distibuted PLCish/DCSish monster of thing, that only they can program because they make the barriers to entry for anyone else so fricking high. And their developers are all located in the third/developing world (and India, in case anyone does not include that place in that category) and there are terrible failings of the ESl variety, of the care and common sense variety, and f**king forget about Functional Safety. Not a one of them has any idea what it means to comply with an IEC 615xx series standard.
    • All of the ECU grounds are to the chassis, the IGN grounds are to the cylinder head and i believe all the OEM body harness are left in original locations, im trying to work out if i can tell if the sensor voltage itself is losing any power to it from the very low ECU voltage. But yeah a manual pressure gauge will help in picking which path to actually chase. Also please dont bully my wiring plan i never designed it to be universally understood hopefully it still can make sense to you, im a wiring virgin.  1 thing i have just noticed the pressure sensor in question relays both pressure and temperature, the temperature reading holds nice and steady despite the low ecu voltage but the pressure reading is the one that jumps around alot so maybe it is really a pressure issue? wiring plan.xlsx
    • Gday, Due to not finding much up to date info on this topic I thought I'd make a thread to get peoples latest opinions/recommendations. Background info -  I've got a S1.5 R33 GTST as a fun project car, mainly for street use and occasional drag strip, apart from all the cosmetic things I'll be doing a full rebuild of the engine with forged internals. Since it'll be getting new cams (kelford) and springs to match I thought I might as well get new lifters and valves while I'm at it, the dash says 160k KMs but the engine seems pretty tired, compression measures about 130psi across all cylinders so I'd like to freshen everything up. This is where I'm tempted to just fork out the extra and go solid lifters while it's all apart, aiming for 400-450kw atw with a flex tune. Assuming all supporting mods (oiling, fuel and all bolt ons) with a lightly ported head and turbo to match (yet to make a decision possibly gtx3582r or similar from Hypergear) I've seen the Tomei kits with just the buckets getting around, Supertech sells most things - Supertech High Performance Cam Followers | Trusted Racing Cam Followers Questions -  Has anyone found the Hydraulic lifters to limit them at this power level? Is it usually found that you can just clean the stock lifters and find they work fine?  Does going solid lifters save any headaches/issues with hydraulic lifters in the future? Any recommendations on other things that will need to be replaced, I know I'll need to get the solid profile cams but can you use the same type of valves and springs/retainers and is it recommended to change the guides and stem seals?    Summary -  Basically looking for pros/cons and wanna know if I'll actually need the extra RPMs from solid lifters or it'll just be bragging rights to say it ReVs OvEr 8000 Cheers
    • Ha ha ha, this stuff they had was installing Toshiba PLCs that were made some time in the 1990s, and they were replacing GEM80 PLCs. To let those two talk (staged upgrade along a ~1.2km long building that was split into 4 sections), was a bunch of WinXP machines running Java gateways... There was no way to put something like ProfiSafe in... Most of the HMI machines were WinXP, with Java program, with a custom button board emulating a keyboard... About the only buttons in the operator stations that went direct to the PLCs was the eStop. There was some interesting design stuff in that place...
×
×
  • Create New...