Jump to content
SAU Community

Recommended Posts

hey, i got an apexi neo afc fitted to a r33, just wondering if anybody else has got the same..

coz my dec setting wasnt tuned in by the tuners..

so any info would be great...

from what it display's it says...

THROTTLE is set to "off", the NEO1 is set to "800rpm", and NEO2 is set to "1000rpm"

so..does this mean NEO1 is low throttle settings?

and NEO2 is high throttle settings?

and when select throttle..from "OFF"...then goes to "0.1%" all the way to 100% if u set it there...

its not a on/off type selection.

so yeah..

confusing..lol

any ideas would be great, thanks

Link to comment
https://www.sau.com.au/forums/topic/214400-apexi-neo-dec-air-settings/
Share on other sites

This is from the AFC Neo Manual... Basically if you have a stock BOV, dont worry about it. If you have an atmo bov/no bov then you can use this to prevent stalling.

If the throttle is rapidly released on a vehicle with a hot wire and Karman turbo airflow

signals, the engine may be stalled by blow-back.

If the throttle is rapidly pushed back, the airflow sensor may react to the blow-back,

disturbing its signals, and then failing in fuel injection response to the deceleration,

causing the engine to stall.

In such a case, it is possible to prevent the engine stall by imposing an upper limit

restriction on the airflow signals by setting“Dec Air”and then shutting off the airflow

signals disturbed by the reverse blow.

If the throttle opening goes less than the value set by“Dec Air”at a rotation speed

lower than“Air Map”engine rotation speed“Ne 02,”airflow signals that are higher than

the airflow usage ratio (or Karman turbo frequency) set in“Dec Air”are not output.

This is to stabilize the airflow signals.

Operations:

Select“Thr”“Ne01”or“Ne02”with the Left and Right keys.

Increase and decrease the set values with the Up and Down keys.

This function is not enabled when“Thr”is“OFF.”

This correction functions at a throttle opening less than the value set in“Thr.”

The rotation speeds set in“Ne01”and“Ne02”are those set in“Ne01”and“Ne02”in

“Air Map.” If a rotation speed in“Air Map”is changed, the one in“Dec Air”is also

changed. (This change is enabled by“Air Map”only.)

Set an output upper limit for the airflow signals that are at the engine rotation

speeds in“Ne01”and“Ne02” If an engine rotation speed is between“Ne01”and“Ne02,”

calculate the upper limit for the airflow signals by linear interpolation. If the

engine rotation speed is lower than that of Ne01 the upper limit for the“Ne01”airflow

signals is adopted.

This function is not enabled at an engine rotation speed that is higher than that of

“Ne02”

ive got a atmo bov..

stalling is not the issue..

i had that problem fixed on my second tune by speedworks in perth..never stalled again from having an atmo bov =)

i just got idle problems..now and again

they go away for a wekk to months..then bad all over again etc..

and i ve tried everything..from cleaning afm, checked plugs/changed plugs etc..ive got spiltfires aswell..

umm...cleaned the iacv..used forton throttle body cleaner to clean throttle body etc..

so yeah..pretty much everything

dont tell me to get a new ecu..coz i knoe..and i will

but for now , hopefully i can fix this problem....

just like any other r25det..lol

so my main problem is.......>

but sometime wen i clutch in the revs drop straight to lik 500rpm

and wen turning it can drop to pretty much 100-200 rpm..coz of the power steering..

so i believe this setting will help wen slowing down and wen i clutch in etc...

  • 3 weeks later...
y use standard bov?

wen new atmo bov is fine?

Because the atmo bov is the reason why the revs are dropping so low. Its doing the same on my R33 and its starting to annoy me, lol. Pretty sure the atmo bov makes the car run richer as well, as my bumper is always covered in black crap just after a few drives.... Thinking of going back to the standard bov myself...

mayb i'll invest in those dual type bov..

wer its also plumb-back

and has a release wen ther a load of pressure

so u can set it to 100% plumb-back, 50-50% etc...or 100% atmo...

would this fix the problem of dying/idle issues etc?????

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm not up to date on the latest, but for basic modifications like pod filter, lower springs etc you can get a modification permit at the time of inspection.  For more serious modifications you will need engineering.  Intercoolers used to fall into the mod permit rule but its been a long while since i looked it up.   Either way you will be able to get it registered, just a case of $300 vs $3k . 
    • Hi everyone! I’m the new owner of a 1996 R33 GTS-T, I’ve purchased this car over from Queensland and brought it to Western Australia and I’ve found that there is a hole cut out in the engine bay for the FMIC that enters into the wheel well (fender liners are in the boot). For anyone that has had to get their car over the PITS here, will this be a major issue?   
    • Yeah I've spotted this one too, whenever it's lotto superdraw week and I'm browsing car sales dot com for my new ride They must be dreaming, maybe it's worth 150k for the link to Brock?
    • 100% accurate!  We are a pack of know it alls....  But, I bet people go to you when they have a problem! I've been on a bit of a clean up rampage too over the past month!  I've thrown more shit in the bin over the past 2 weeks than I have in the past 3 years combined! Anyway, it's all good fun being different! My wife sometimes does not agree!  
    • ADHD in all form isn't about "can focus, or can't focus" or is hyper active or isn't etc.   It's all a dysregulation. Either time feels to be stationary, or time just vanishes in a split second. We are either under focussed on the task at hand (as we're over focussed on our surroundings) or we have no idea an atomic bomb went off beside us as we're so hyper focussed and locked in on things.   Not to mention the rapid fire thought process. What it takes a "normal" process to think up a solution to a problem, ADHD will be able to give you 5 different ways to solve the problem, and the pros and cons of each. While we can be highly impulsive and lack the ability to "control ourselves" we can also become paralysed with the inability to make a decision for ourselves. While most of us have an OCD like requirement for perfection, we lack the ability often to remain focussed to get things to a perfect state. Those with undiagnosed ADHD as adults, can often find the last part actually stops them ever attempting to do things that they have the ability to do, as the reasoning is often "if I can't do it perfectly, it's not worth doing"   As for projects... Ha ha ha, I still need to take the other half of my wall trim down in the Fiance's office so I can paint it. Need to finish digging and running the back yard drains, my R33, getting the Ninja bike registered (now being sold), the moped project, fixing either of the lawn mowers so they're reliable, along with a myriad of other things.   It's why I've been going through lately and just being brutal and clearing projects off that I won't actually ever complete. IE, moped will go to the tip, or be given away, bike is being sold, Subaru project being sold, some parts for other projects given away. Or I've been making myself focus on one thing at a time, by ticking off the smallest quickest ones first.   There's also a reason by our mid twenties we seem to be "know it alls", as we've all been down some of the weirdest and oddest rabbit holes when you follow the dopamine trail. It's often also why we're more a jack of all trades, but not a master of one.   However, pretty much all of my hobby projects, in one way or another, all come back around to automotive. That's my zen area.
×
×
  • Create New...