Jump to content
SAU Community

Need Some Rubber Hose Hopefully Today/tonight

PWND

By PWND,
in Queensland

 Share

Recommended Posts

PWND Grand Master

PWND

Posted
Posted

Just started fitting a turbo smart blow off valve, and noticed that the hose that is connected to the standard plumb back outlet is too stiff to bend it the extra two centrimeters to fit onto the new blow off valve.

just wondering if somebody has some spare hose around the browns plains area that i could use, that is the correct width. have already gone around the yard and shed measuring up garden hose, but couldn't find anything that would fit.

if that fails, is it possible to make the blow off valve non plumb back until i do get the hose tomorrow, or should i fit the old one back on? what hoses should i block off if i do make it non plumb back for the time being?

cheers

PWND Grand Master

PWND

Posted
  • Author
Posted

i probably should have specified that anyway

need something 25mm inside diameter. wall thickness not really important, as long as it doesn't melt in my engine bay.

had a quick look around repco and hardware stores today, and still couldn't find anything.

if i still have no luck, might take a drive down to moss street. bound to find something there.

R33S2 Grand Master

R33S2

Posted
Posted

I had the same problem when doing mine, I bent the pipe a bit with a bar with the same ID and braced it against the engine bits with a block of wood, so it lined up better (wrong angle but inline) and used the normal rubber pipe with clamps. I have some more of that clear pipe as well.

post-17300-1208078927_thumb.jpg

PWND Grand Master

PWND

Posted
  • Author
Posted

haven't given that a go yet. I was too afraid i was going to snap something.

might have a walk downstairs now, see how i go. otherwise am in logan for work on tuesday anyway, so was going to pop by a couple of the shops there and see if i could find something.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      R33 GTR lift points for hoist

      By sunsetR33 · Posted

      Hi all. I am aware there is lots of discussions about jacking points, where to lift the car and what not. But as usual just a lot of "in my opinion" and nothing definitive, and everyone does it in a different way. I want to hear from some experienced people on which points on the car it's okay/safe/recommended to lift the car using a four point hoist/lift. I will attach some images of my underbody. Sills are largely okayish, the driver side jacking point is pretty mangled though and it looks like the underfloor is slightly pushed in too, but I might be wrong. In the German Skyline forum, the consensus is to use the sidemember chassis rails in the front and the rear subframe? bushing in the rear. I know the manual says to never use the sidemember for loading but lots of folk do it and it was definitely done on my car too as they are slightly bent too. Based on the images, what points do I use to not make the already present damage worse? I'd use wood or rubber blocks to spread the load across a bigger area of course. Driver side sidemember and jacking point mangled one) https://imgur.com/a/eKjzrJX Driver side rear jacking point https://imgur.com/a/W3DWF1P Passenger side sidemember and jacking point https://imgur.com/a/65UvIJe Passenger side rear jacking point https://imgur.com/a/h3k7j53 We can also see some underbody rust but so far it all looks somewhat treatable and nothing that requires a Yoshida style restoration.
    • MBS206
      Ticking Sound On Idle - Rb25

      By MBS206 · Posted

      Have you put an aftermarket oil pressure gauge on and verified your oil pressure?   Noise being on the block, on exhaust side, how high up the block does it seem to be? It could be the VCT system getting cranky, especially if it's mainly at idle, and when warm, as that'll be your lowest point for oil pressure. Could be showing that oil passages / VCT solenoid are blocking.
    • WARLORD
      injectors top feed for sale

      By WARLORD · Posted

      Deatschwerks 1800cc sold
    • GTSBoy
      Ticking Sound On Idle - Rb25

      By GTSBoy · Posted

      Well, hydraulic lifters will get noisy if they are dirty/fouled in some way, and exactly how that manifests will depend on exactly what schmutz is where. There is a procedure on here somewhere for dismantling and soaking/cleaning them. Replacing them with new is about 50% of the work and about 5% of the money!
    • myrbgivesmeheadaches
      Ticking Sound On Idle - Rb25

      By myrbgivesmeheadaches · Posted

      Thanks for the reply @GTSBoy this is is a hydraulic lifter engine. Yea right i did not realise the lifters were supposed to be compressible while installed. I could push them down but i had to lean almost my while body weight on them.  I have never heard of a lifter/ lifters ticking only at hot idle and getting worse the hotter it gets. I have owned a few jdm cars with noisy lifters. This noise is slightly more subtle, it is more of a sharp gentle metalic tic than the solid and more loud tapping I've heard on lifters. I have used a metal rod, alloy tube, hose and stethoscope and could not find the source of the tick. But it appears to be loudest on the actual engine block behind the exhaust cam gear and next to the oil filter. I had mate (40 year old mechanic) go over it with me and he couldn't find it either..  Could it be a cam seal issue of some sort?  Cheers  
×
×
  • Create New...