Jump to content
SAU Community

Recommended Posts

NISMO PROTO GTX-1 2500R

(IVE BEEN MEANING TO GET THIS UP FOR AGES - APOLOGIES FOR THE DELAY !!)

HERE IS NISSAN'S / NISMO'S / OMORI FACTORY'S (WELL MINE ACTUALLY) 1993/1995 R33 SKYLINE PROTOTYPE SINGLE TURBO 2.5 LITRE REAR WHEEL DRIVE 4 WHEEL STEER NO ABS SPORTS COUPE "BITUMAN SNIFFING" STRAIGHT SIX THAT PROVED TOO POWERFUL FOR A JAPANESE DOMESTIC MARKET RELEASE. ONLY 3 OF THESE EACH HAVING SLIGHTLY DIFFERING SPECIFICATIONS WERE BUILT WITH THIS CAR PRODUCTION "NO. 2" (P002) THE ONLY COMPLETE AND INTACT EXAMPLE KNOWN TO EXIST.

BEST SUITED TO WIDE OPEN SPACES THIS CAR COMES INTO ITS OWN AT AROUND 170KPH (TOP SPEED 285KPH) WHERE ITS IMPECCABLE BALANCE OF RAW POWER AND CRISP "POINT & SHOOT" RESPONSIVE HANDLING CAN BE CONSISTENTLY ADMIRED ENJOYED AND RESPECTED.

POWER - 460PS

POWER - AT THE REAR WHEELS - 273.8KW

POWER - AT THE FLYWHEEL - 375KW

POWER TO WEIGHT RATIO - 0.19KW/KG

ENGINE HARDWARE:

RB-X GT 1 BLOCK - NISMO INTERNALS - 600CC NISMO INJECTORS - GT-R FUEL RAIL AND INJECTOR CRADLE - CARBON FIBRE COLD AIR INTAKE WITH APEXI AIR FILTER - TRUST TD05 JOURNAL BUSH TURBO CHARGER - CUSTOM NISMO INTERCOOLER - EXTRUDE HONED PLENUM - PLUMB BACK BLOW OFF VALVE - NISMO 4.2L PER MIN. FUEL PUMP - SPLITFIRE IGNITION SYSTEM - APEXI POWER FC ENGINE MANAGEMENT SYSTEM - GREDDY PROFEC SPEC B II BOOST CONTROLLER - OIL COOLER - 3IN FRONT PIPE - 3IN STRAIGHT THROUGH MANDREL BENT EXHAUST SYSTEM WITH 4IN FUJITSUBO CANNON - Z32 AIR FLOW METER - APEXI ELECTRONIC BOOST GUAGE.

DRIVETRAIN:

GT-R GEAR SET - EXEDY CERAMIC 3 PUCK CLUTCH AND LIGHT WEIGHT FLYWHEEL - GT-R AXLES - NISMO 1.5 LIMITED SLIP DIFFERENTIAL WITH 4.4 FINAL DRIVE RATIO.

SUSPENSION / BRAKES:

BILSTEIN TRACK SHOCK ABSORBERS FRONT AND REAR WITH TANABE SPORT SPRINGS (LOWERED 20MM) - GT-R STRUT BRACES AND SWAY BARS FRONT AND REAR - BREMBO GT-R BRAKE CALIPERS WITH DBA 5000 SLOTTED ROTORS FRONT AND REAR - NISMO MASTER CYLINDER BRACE - ENDLESS COMPETITION BRAKE PADS.

WHEELS AND TYRES:

17IN X 9IN R33 GT-R WHEELS - DUNLOP SPEC-R 245/45/17 TYRES.

BODYWORK:

NISSAN GUNMETAL PAINTWORK (KH2) - GT-R STYLE FRONT BAR LIP AND GRILLE - GANADOR AERO MIRRORS - GT-R REAR WING ASSEMBLY WITH N1 CARBON FIBRE BLADE - BADGES DECALS AND IDENTIFICATION PLATES BEARING "NISSAN" "OMORI FACTORY" "NISMO" "GTX-1" "2500R" "RB-X GT 1" "P002" AND "PROTO".

INTERIOR:

GT-R FRONT AND REAR SEATS - NISMO STEERING WHEEL GEAR KNOB AND PEDALS - APEXI REV/SPEED METER - GREDDY TURBO TIMER - DEFI OIL/WATER TEMP/PRESSURE GUAGES - KENWOOD KDC 2020 HEAD UNIT WITH 600W AMPLIFIER FRONT SPLITS MIDS/TWEETERS REAR PARCEL SHELF 2 WAY MIDS AND BOOT MOUNTED 10IN SUB WOOFER.

WELL I GUESS THATS ABOUT IT...... OH YEAH !.....

SORRY - BUT ITS NOT FOR SALE :down:

CHEERS MALCOLM :D

post-9783-1208757733_thumb.jpgpost-9783-1208759372_thumb.jpgpost-9783-1208759749_thumb.jpgpost-9783-1208760061_thumb.jpg

post-9783-1208760410_thumb.jpgpost-9783-1208761168_thumb.jpgpost-9783-1208761710_thumb.jpgpost-9783-1208776274_thumb.jpg

post-9783-1208762118_thumb.jpgpost-9783-1208762262_thumb.jpgpost-9783-1208766628_thumb.jpgpost-9783-1208766885_thumb.jpg

post-9783-1208767672_thumb.jpg post-9783-1208767805_thumb.jpgpost-9783-1208769982_thumb.jpg

post-9783-1208768097_thumb.jpgpost-9783-1208768231_thumb.jpg

post-9783-1208768362_thumb.jpgpost-9783-1208772495_thumb.jpgpost-9783-1208768563_thumb.jpgpost-9783-1208768687_thumb.jpgpost-9783-1208814951_thumb.jpg

post-9783-1208815107_thumb.jpgpost-9783-1208815308_thumb.jpg

post-9783-1208815469_thumb.jpgpost-9783-1208816112_thumb.jpg

post-9783-1208816635_thumb.jpgpost-9783-1208816274_thumb.jpg

post-9783-1208816413_thumb.jpgpost-9783-1208822281_thumb.jpg

post-9783-1208829175_thumb.jpgpost-9783-1208829527_thumb.jpg

post-9783-1208829736_thumb.jpgpost-9783-1208832835_thumb.jpg

post-9783-1208761928_thumb.jpg

Edited by malcolm
  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/215823-nismo-proto-gtx-1-2500r/
Share on other sites

wasnt this car featured in High performance imports very recently ? Lucky owner...wish I had it

Sure was - have had lots of requests to make use of the great pics Dean from HPI took and get it up on SAU for those who didnt see the magazine - malcolm - :down:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It only looks tidy, as most of the stuff that was on the whole back wall, is now in the trailer to go to the tip, or has been shoved in my 2.2x2.4m "Spare parts room", and now I can't get to anything in there Ha ha ha I could definitely do with a bit more space, but I'd just end up with your problems I'm going to enclose the car port beside the garage, and move a lot of stuff into it I think. OR... It will be setup as a fabrication area, and the main garage will have parts storage in it. I'm not sure yet... Need some pictures of that big shed you've got with the bikes and Skyline in
    • No. I think it's gone. 😭 I think you can get body coloured ones on eBay so I think I'll get one of those... Or just hang a red ribbon from the hole and whack a TOW sticker next to it.
    • Can't say I've had a bad experience with one on my car, then again it only gets washed once or twice a year... The wheels on the other hand, get a good spray often due to my shitty dusty pads.
    • @MBS206 thats pretty neat and tidy to me!  I'll get a photo of mine when I'm out there next. It might require multiple photos to understand the scale of the atrocities though... In total I have 4 sheds of varying sizes and layouts. Main shed is 14x8, second shed is 3x8, third shed is 11x2.5, fourth shed is around 6x4.  All are pretty much full.   The main goal of my cleaning tsunami is to make the main shed predominantly car and motorbikes only. Second shed is my metal fab room (2 x bench grinders, drill press, bench belt sander, metal band saw, scrap metal storage and some of my garden tools.  3rd shed is more bigger garden stuff, storage for engine crane, jack stands, concrete grinder, concrete mixer, air compressor lives there, and it now has two 2mx2m pallet racking shelves with itemised boxes holding building stuff, electrical stuff, plumbing stuff, etc, etc.  The 4th shed is Ryobi electric ride on mower, mini boom sprayer, ancient Kubota tractor, more garden stuff!  I have got a lot of shit....  Then there's the pool house (8mx4m) and the pool pump shed (4mx4m).  I built all of the sheds over the 11 years we've been here.  The main shed was a Ranbuild kit, the rest are all custom made to fit the areas available. Building the main shed taught me a LOT as I had no idea about building anything prior to that!  I've still got one more in me. It will be my man cave which I poured the extra concrete for way back when I poured the concrete for the main shed. The idea is the Skyline will be a centre piece of the main cave once (if...) it's finished.  I told my now 14 year old son yesterday that I will 100% drive him to his year 10 formal in 2 years. Still a long way off but at least I now have a date to work towards! 🤣
    • Modern oils are amazing. Add tyres to that as well.
×
×
  • Create New...