Jump to content
SAU Community

My New 32

BANGN

By BANGN,
in Western Australia

 Share

Recommended Posts

BANGN Experienced

BANGN

Posted
Posted (edited)

after the little incident with my last 32 I have finally got the money to buy another one.

I purchased it from NSW as prices over there are a little bit more nicer than WA prices.. obviously WA imports hold there value better than eastern states.. so in the end i payed 6200 for this neat little number in complete stock condition.. its automatic but that doesnt matter as i have a complete skyline in the backyard to transfer it into a manual :( It also has factory fog lights and done 90k on clock

IMAG0265.jpg

IMAG0266.jpg

IMAG0267.jpg

IMAG0269.jpg

IMAG0270.jpg

and here is the toys that will be going on it when it gets here :)

P4250035.jpg

HKS Cooler, 044 fuel pump, tein coilies, dba 4000 slotters, rb25 turbo, AFCII, 600hp rated seco pressure plate

I also have a aluminum bonnet, gtr grill and gtr wing too :P

Cant wait when it arrives.. thinkn on getting [bANGN] plates for it as I want a bee*r limiter.. I have a screamer on order atm for it as well :(

Edited by BANGN
Link to comment
https://www.sau.com.au/forums/topic/216468-my-new-32/
Share on other sites
Krazy 32 Contributor

Krazy 32

Posted
Posted

nice car dude gl with car...do you think a front mount cooler kit would look good on that bumper because thats the same one i have and the fog lights aswell... i still cant decide if i should get a front mount because i have a feeling it wont be seen and also not look good what do you think??? cheers dude

Link to comment
https://www.sau.com.au/forums/topic/216468-my-new-32/#findComment-3823479
Share on other sites
BANGN Experienced

BANGN

Posted
  • Author
Posted (edited)

iv painted my hks cooler black as i dont want it to be seen. I want sleeper effect. i just hope it fits ok with the driving lights on the bumper.

yeh i brought him down a bit :P only ross I know drives a 05 swift

im thinkn either white or black rims for this too

Edited by BANGN
Link to comment
https://www.sau.com.au/forums/topic/216468-my-new-32/#findComment-3823523
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • soviet_merlin
      NC MX5

      By soviet_merlin · Posted

      A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
    • MBS206
      Shoota's R33 GT-R RB30/26

      By MBS206 · Posted

      I was more thinking so it doesn't flop around as much rather than for rotating it. Once you have the balance right, it should rotate well enough, depending on how much resistance there is on the pivot. I think you said the pivot point was on a bearing though didn't you?
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      You can get them with the worm drive rotator but I was too tight to pay another $250-$300 so manual labour it is! I don't think it will be too hard to rotate though. 
×
×
  • Create New...