Jump to content
SAU Community

Recommended Posts

Hey guys, cos im lazy, and i don't wanna look at the phone book, and cos i want your experiences,

i wanna know where there are jap wreckers in perth, and your personal experiences with them

the only 1 i can think of off the top of my head is in welshpool near where i used to work, on Pilbara st i think... not to sure, don't remember what its called:rolleyes:

looking for a few little bits n pieces

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/
Share on other sites

hey memphis, i need driver side door pillar thingy(between the driver mirror and the rear quarter mirror), mine got ripped off when some guy tried to break into my car (good thing i have metal sleeved tint)

hope u can ask them for me, my number is 0401290390,pls give me a sms

Aidwin

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-458597
Share on other sites

jap motor sport in sydney and just jap in adelaide are both very good and will post most things over including frieght cheaper than any company in perth could sell it to you.The only other person you mite want to try is Mayhem on this site as he sometimes brings in half cuts.hope this helps.

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-460573
Share on other sites

In cannington there is japwreck and Nispart Datpart I am not sure of addresses. One is near bunnings, the other near the big WA salvage. For common older stuff Niss part but Japwreck have engines mirrors front cuts strut bars etc etc.

Actually the most helpful cos i needed some small plastic wiper box screws was pulsarwreck around the corner for nisspart.

Link to comment
https://www.sau.com.au/forums/topic/21652-jap-wreckers/#findComment-461040
Share on other sites

  • 2 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Latest round of updates on the car. I purchased and installed a SWS clutch slipper to help with 60ft times and got some second-hand good condition 275/40R17 Hoosier DR2 radials. Test and tune in November showed the tyres were an upgrade over my over 15 year old mickey Thompson's and I got a 1.8 second 60ft and pb et of 11.71 but even then, that run wasn't great due to rain and driver error (the event got called off 10 minutes later fast forward to the weekend just gone 25th of Jan and there was finally a break in the weather to let racing happen. The first run the track was slippery and only managed a 12.1@129 Second run the track was better and got a new pb et and mph: 11.54@131   Lith and I then worked out that I installed the previously mentioned clutch slipper incorrectly and its never been working, and I had just been dumping the clutch the entire time, we also noticed it was on street boost and not race boost. So I lined up for a third run with the car turned up in the first two gears, but the passengers side axle objected to clutch dumps and left the chat which stopped my weekend.   so there will be another attempt in the future once I replace the tyres as they rubbed and are stuffed now. but a low 11 should be on the cards.
    • Ceramic coating and heat shielding, you mean?
    • Turbos don't require pulling the motor apart so that's "easier". I would recommend the Nismo R3 turbos instead if you want to do stock twin turbo. It doesn't make as much power as the 2530s but it's only like ~50 whp off the mark and should have better response (ball bearing CHRA, slightly smaller turbo). A local that went with a Garrett G30 and 6boost manifold recently nearly burned his car to the ground after the hood insulator started melting and and burning so if you go single turbo I recommend doing a lot of research and validation work to make sure you don't do the same.
    • New rear lights, filler panel sprayed, cleaned and back together    before, during, after shots 😍
    • 100% is gyprock, I agree. Slip of the keyboard. Haha! I left my indicator bulbs out to save a bit of weight.
×
×
  • Create New...