Jump to content
SAU Community

Recommended Posts

Hey guys/girls

Car: 1992 Nissan Skyline R32 GTS-T

Km: 79, 699

ok let me explain the whole chain of events ( it may help solve the problem I’m having). ok today at about 1 i was driving my car, i stopped it and was watching a movie in the car for a bit. About 1 hour later i tried to start it but nothing was working. i checked the voltage by using my radar detector, it showed 10.8V. also i do not have a sub connected, i do have 1 amp connected however it was only running a pair of 6 y 9's and I’ve had my DVD player on before for 3 hours at a time and never has this problem arise. any way so i tried pushing it up a hill and then doing a rolling start. However that didn’t work, i checked the voltage again and i was now sitting on 8.9V which is even worse. and this is with the stereo and everything turned off. then i checked and noticed that my parkers (front and rear) lights where on including the interior lighting. i checked if by accident i had turned the knob to parkers, but they were also off. i then checked again and got a reading of 6.3V and after that i couldn’t check as my radar detector said "battery to low". I Rang a mate of mine who has a WRX he bought jumper leads , we connected them however my lights still stayed dim and i wasn’t getting any power through to my car. finally, i removed a cable that is connected to the positive terminal off the car ( i don’t know if all skylines have it but i know the r32's have a wire that is connected too the red terminal. it is one of those wires that has a clip to unhook it and if you do unhook it. all the power to the car is shut off.) after i removed this and waited a while and then connected the wire again i had 10.1V reading, however it still wouldn’t kick over. and still my lights where on and i couldn’t turn them off . after a while off trying it finally randomly kicked over ( while jumper leads still connected) however my idle was really ruff and i revved it a bit and a pop noise came and the car's revs dropped and stalled also white smoke from the rear with a bit of burning smell came. any way i tried again and it started, however the revs are ruff and there is a bit of lag when it hits 2000rpm it stops revving and just stays there , until you plant your foot it will go over it. However the engine also has a whining noise now. i drove it home asap before something stuffed up again on the way. i found out at lights my idle would randomly start to drop below 1000rpm( the speed my car usually idles at) and id have to put my foot down a bit. also i still couldn’t turn off the lights . when i got home my lights where still on so the only thing for now i could think off and did was pull out the 20 Amp fuse( in the interior fuse box) which cuts power to the parkers and the interior dash lights.

Does anyone know what is wrong with my car or what it could be..or how i could fix this problem

thank you very much

niran

Link to comment
https://www.sau.com.au/forums/topic/216986-electronic-faliure-help/
Share on other sites

omg! ok i went and checked and omgg!!! ahahah that was it.. omg that is so embaracing.. prob it i have a aftermarket kit. therefore i never even knew the button was pressed thank you SO much! lol saved me from pulling all the wires out thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • yeah i agree paint match stops it from standing out so much, oh that's actually really good to know i was wondering if it would help with air flow now actually having an outlet in the bonnet. Will have to focus on ducting into and out of the radiator now to make the most of it.
    • I would paint match the whole thing to avoid unwanted attention  I had a similar bonnet, paint matched, on my old R33 GTST, but mine was a fibreglass jobbie made by Blitz in QLD, they work extremely well for radiator efficiency and under bonnet temps
    • Does anyone run this kit with factory plenum? Does the adapter and bosch tb fit under factory strut brace? I wanted to get this setup before going forward facing manifold. Thanks
    • small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
    • I think it's bound to happen, you finally get it all perfect, and bam, something will happen. I took a while to get a Commodore rear quarter repaired where a P Plater clipped it. Two days after getting it back, Sarah wiped it out on a concrete pillar in an underground car park... This is why I take forever to repair them, it stretches how long until it gets bent again... 😛
×
×
  • Create New...