Jump to content
SAU Community

Recommended Posts

Hey guys i recently stuck my car in to get tuned, they reached about 9 psi and started to have issues with knockin.. etc scratched their heads for a while and worked out that the air fuel ratio was changing dramatically between runs without them changing any settings.. between high 10:1's to low 12:1's on boost

my mods are intank walbro fuel pump, power fc, fmic, full exhaust n a blitz ebc.. ive tried earthing the fuel pumps earth to the battery and the results remained much the same

any ideas would be greatly appreciated

Cheers

Jarrod

Link to comment
https://www.sau.com.au/forums/topic/217183-varying-afrs-on-dyno/
Share on other sites

yeh i would of liked them to have done this but i wasnt there as i was at work, had a mate take it up.. the ppl that dynod it turned out to be completely useless coz they could of chekd the coilpaks n pressures while it was on a dyno, n i don't want to have to send it to another place n another dyno just to get the problem resolved, just would like to know some of the most likely causes.. the earth wire on the in tank fuel pump is exposed n a little corroded.. that couldnt be causing the issue could it?!!

located in perth guilt-toy, thanks for the pointers guys ill probally replace the fpr first and over the fuel pump becuz its the cheaper one to replace... are they any fpr's that are direct replacement that dont need adjusting? is the sard one any good?

located in perth guilt-toy, thanks for the pointers guys ill probally replace the fpr first and over the fuel pump becuz its the cheaper one to replace... are they any fpr's that are direct replacement that dont need adjusting? is the sard one any good?

It goes in this order

Test

If broken

Replace

Dont just go replacing random parts dude, test them, find the problem and then fix it the first time rather than bringing more problems into the equation

you said it was doing it under load, you must therefore test it in the same fashion

You 'can' do it on the street, but you wont be able to see the AFR's without a wideband and a proper read out.

Take it back to the dyno place and demand they do a semi-reasonable job. They did a half assed one last time

yeh i got a wideband with a datalogit.. i rang up the shop this morning n askd why they didnt test the fuel pressure n they claimed coz they were borrowin the dyno they didnt have their tools with them to do it ... so now i have the dilemma of sendin it to another shop with a dyno to diagnose.. why im tryin to just fix it myself coz all the shops in perth seem to be useless..

anyone know if a 180sx fuel pump will work in a r33 gts-t?!? i borrowed a girl my stock one because she thought her one was broken n claimed several ppl said it was the fuel pump so after we installed the fuel pump for her we found out she had a kink in her fuel line, when and got home, i tested her fuel pump n it still worked.. id swap them back sooner but shes in bali for a while .. so would it be fine to test a 180sx one in the skyline for a run to see if the afr's hold more steady on the wideband

ahh think i might just buy the new fuel pump.. standard wiring isnt the best anyway the earth wire is exposed and a little corroded so ill buy a full replacement one... so tomei or nismo?!! i know you probally can't go wrong with either but what one would allow for more hp?

Cheers for all the advice aswell guys

  • 2 weeks later...

hey guys sorry to bring up an old thread but im still having afr troubles, i bought a new tomei fuel pump to replace the walbro, no change still playing up... bought a sard adjustable fuel pressure regulator.. same results...varies between 12 n 14.4 around the 6psi mark... and varies between 9.5 and 12.2 around the 10 psi mark... im measuring the results with a innovative motorsports lc-1 hooked upto a lap top... has anyone else got any other ideas that could cause the results to vary so much

Cheers

Jarrod

Edited by jarrod83

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few more recent pics
    • full send the cnut, do this   fark the wrapping and/or stick on siet. These guys are the ones to go to: https://www.realthermo.com.au/  
    • Just had a look, they don't. Fuelling on the base map is purely alpha-N, and the ignition table is MAP. Remember it's just a base map to get the car moving  
    • Hi everyone, I’m Dave from Canberra. Here's a few pics of my 1992 R32 GTST coupe which I imported back in 2006. Only mods so far are HKS Hi-power cat back exhaust, K&N filter, ATC Volanti steering wheel, Pioneer stereo, amp and sub. This was my daily driver up until 2015 and sadly hasn’t been driven at all in the last 5 years due to marriage, work, and kids taking up most of my time and spare cash.As such its in need of a bit of TLC and one of my goals for this year is to get it back to running condition and maybe look into club/historic rego. I’ve joined SAU so I can ask a few questions along the way (although I promise to google Current Problem +SAU beforehand!)
    • From talking to the mx5 guys the NC doesn't actually need bonnet vents like the earlier NA and NB models, due to a better designed cooling system and undertray design There's plenty of them used as street cars and weekend track toys running anywhere from around 170 to 250kw with stock non vented bonnets, I initially was going to get some bonnet vents, but, as they are not actually required, I'll put vents on hold for a while and just monitor temps, though I do need to get something to actually monitor engine oil temps though, coolant temp can be pulled from the OBD2, but the oil gauge in the car is not actual oil temp, it is only a calculation based off coolant temp and RPM ☹️ They do recommend upgrading the radiator, which I have already done with a triple pass, and the only other thing they recommend for a street car is heat management, like I talked about above to protect bits in the engine bay from radiant heat, and to either replace the nearly 20 year old plastic coolant expansion tank, which I have done, or get a aftermarket alloy jobbie for some bling They did also say that if I wanted to track the car on occasion a oil cooler and sump baffle would be required, and as I already have had a sump baffle installed when the engine was out......... I'm going to get a oil cooler with a thermostat....... just in case I do eventually track the car, but probably not, but still maybe...🤪
×
×
  • Create New...