Jump to content
SAU Community

Recommended Posts

Hey guys, over the last few weeks i have been talking to a few people about whats happening to my 34, after speaking to a few of these people, im starting to think my 34 nismo is not an authentic one... is there any way i can tell, like check over the internet or something??

Edited by A31StRuCK
Link to comment
https://www.sau.com.au/forums/topic/217310-is-it-authentic/
Share on other sites

if u bought from powerplay than its nismo

* GT-R - 2.6 L RB26DETT twin-turbo I6, 332 PS (244 kW, 392 N m) (advertised as 280)

* GT-R V-Spec - Additional aero parts, brake ventilation ducts, diffuser.

* GT-R V-Spec II - As above + carbon fibre bonnet with NACA duct.

* GT-R N1 - Blueprinted N1 motor, no A/C, no stereo, no rear wiper, basic interior trim. (only 45 made)

* GT-R M-Spec - Leather interior, softer suspension with "Ripple Control" dampers, heated seats.

* GT-R V-Spec II Nür - As above V-Spec II + N1 motor, 300 km/h speedo. (only 750 made)

* GT-R M-Spec Nür - As above M-Spec + N1 motor, 300 km/h speedo. (only 250 made)

* GT-R NISMO R-tune

* GT-R NISMO Z-tune - 2.8 L (bored and stroked) RB26DETT Z2 twin-turbo I6, 500 PS (368 kW, 540 N m) Z1 and Z2 (Only 20 made)

Link to comment
https://www.sau.com.au/forums/topic/217310-is-it-authentic/#findComment-3836910
Share on other sites

It's not a nismo car, and technically speaking it's not really a nismo kit (although other's would argue otherwise)... it's actually an Aero kitted factory GTT. Sorry to say, based on my knowledge of GTT's you don't have a "nismo" car as per se.

Link to comment
https://www.sau.com.au/forums/topic/217310-is-it-authentic/#findComment-3836981
Share on other sites

Might be on the auction sheet, but you probably won't have that. And I take it you don't have japanese service manuals? The thing is most imports are wound back... often more than once, too many points where it could be wound back ... e.g. in japan, at auction, in australia by the importer, in australia by the dealer. If the motor and body is in good nick be satisfied with that.. with all RB's it's all down to how well it's been serviced and looked after generally.

Link to comment
https://www.sau.com.au/forums/topic/217310-is-it-authentic/#findComment-3837004
Share on other sites

ok also is there some way to find out if the 100 thou service has been done, obviously i recieved the car before 100,000 so there would be no stickers on the door or window... car runs smooth as but cant really push it as its due the service, but i dont wanna spend that money if its already been done ya know!

Link to comment
https://www.sau.com.au/forums/topic/217310-is-it-authentic/#findComment-3837043
Share on other sites

If you're lucky there's a sticker that sometimes comes with a new timing belt, that gets placed under the bonnet. If you don't have one, then I suggest you change it (and the waterpump, and the plugs, and all the other things you do at the 100k service at the same time).

Link to comment
https://www.sau.com.au/forums/topic/217310-is-it-authentic/#findComment-3837049
Share on other sites

Here is the quote I got from boostworx for a 100k service.

$170 water pump

$95 timing belt

$240 labour

$77 service / safety

$65 oil

$140 redline (tran + diff)

$55 coolant

$145 dyno

$140 platinum plugs

Whoa, man thats alot eh, i can get the parts for the 100 thou service for like $360... thats belt, bearings, water pump the whole lot!

then all i need is to get the oils and fluids then get someone to do it for me!!

anyone on here know how?

Link to comment
https://www.sau.com.au/forums/topic/217310-is-it-authentic/#findComment-3837065
Share on other sites

Well that's the list price, and it's not really that much when you think about it - just shop around and you'll see. Especially given that boostworx found a AFM problem on the dyno (picked up a lost 15rwkw), and a front suspension bracket issue... good to see some mechanics still know their trade well.

But yeah if you want to save some, do the fluids yourself, the plugs even. Not really hard dropping the oil... undo the screw on the bottom of the sump, dump the oil into a pan, change the oil filter, put screw back on, fill up with motul oil, and bob's your aunty.. umm uncle even.

Link to comment
https://www.sau.com.au/forums/topic/217310-is-it-authentic/#findComment-3837075
Share on other sites

there are certificates issued for parts fitted by nismo after sale but doubt you have them. Is there even such a thing as a nismo gtt r34? it was probably just a gtt some stuck a few nismo things on and said it was a nismo gtt? Did you pay a premium for the car because they claimed is was a "nismo"?

Link to comment
https://www.sau.com.au/forums/topic/217310-is-it-authentic/#findComment-3837167
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I'm looking for a direct bolt on turbo upgrade for my 93 R33 GTST.  Anyone have experience with this Greddy T620Z turbo upgrade? I'd like to be able to run about 300hp to the rear wheels without putting too much strain on the turbo. I do daily drive the car.  Pretty stock car with basic bolt ons (exhaust outlet, down pipe, high flow cat and catback exhaust along with intake and FMIC).  I'l probably have a Haltech plug n play on the car before installing the turbo. https://www.greddy.com/products/turbo-upgrade-ecr33-er34-t620z-rb25-11520057   Also, any thought on this much boost on a 30 year old motor with 250,000KMs?  Engine feels/sounds strong for what it's worth.   Thanks you in advance!
    • Hey all, I'm working on a project car and I believe I made some mistakes. I'm looking to remove the clear coat from my car on most panels (except for panels where the paint has blistered, I will sand this), but wanted to know if these steps are correct?   1) Get a red scuff pad (abrasive one) instead of sand paper to remove the shine from the surface 2) get 400 grit sand paper and go over the entire car with a random orbital sander so the surface is smooth and the primer can grab onto something 3) On the blistered paint, go over it with around 120 grit sand paper, go to 240 to smooth out the scratches, then finish on 400 grit. Anything to add in here or any feedback?
    • Agreed, another vote for the Haltech CAN wideband.  No voltage offset errors is a beautiful thing.
    • Just get a Haltech CAN wideband, no need to wire any delay circuits, or relay, etc. Since I've moved to a Haltech CANbus wideband, I have not replaced a single sensor for over 5 years (if not longer, can't remember when moved to Haltach).
×
×
  • Create New...