Jump to content
SAU Community

Series 1 And Series 2 Rb30 Blocks

NYTSKY

By NYTSKY,
in Engines & Forced Induction

 Share

Recommended Posts

Sydneykid Grand Master

Sydneykid

Posted
Posted
Hi all,

Im picking up a series 1 RB30 block,does the series 1 have oil squirters or is it the series 2 that has them? (piston)

No RB30's that I have ever seen have block mounted oil squirters, that's Commodore RB30E, Commodore RB30ET, Nissan Skyline RB30, Series 1 or Series 2. They all have the basic 1980's style conrod oil holes.

Is the series 1 block a good block to use in a 25/30 combo?

Any good block is a good block to use.

Cheers

Gary

den001 Proficient

den001

Posted
Posted

there is another block that can be used, but it does require a fair ammount of work to the block to be able to adopt a twin cam head,its do-able and it weighs about 30ks heavier than a standard rb30 block, the cylinder walls are a shitload thicker than a conventional rb30 block and will last well over the 1000 wheel hp mark.....

this particular block comes with piston oil squiters.

2jz is in trouble now....

NYTSKY Grand Master

NYTSKY

Posted
  • Author
Posted
there is another block that can be used, but it does require a fair ammount of work to the block to be able to adopt a twin cam head,its do-able and it weighs about 30ks heavier than a standard rb30 block, the cylinder walls are a shitload thicker than a conventional rb30 block and will last well over the 1000 wheel hp mark.....

this particular block comes with piston oil squiters.

2jz is in trouble now....

And this mystery block is......?

Sydneykid Grand Master

Sydneykid

Posted
Posted
And this mystery block is......?

My guess is RD28T, 2.8 litre (2825cc) turbo-charged diesel 6-cyl, bore: 85mm, stroke: 83mm.

I looked at it about 6 years ago, there is a lot of work required to fit the RB30 crank (86 mm stroke) and conrods. Plus the cylinder head studs don't line up with an RB25/26 head. The water jacket needs modifying and the oil feed will need some external help.

Cheers

Gary

den001 Proficient

den001

Posted
Posted

thats teh 1, deisel, runs somthing like 22:1 compression. found in the nissan partol 92 models.... there is about 4 to 5 grand in block modification, there is a rear water jacket that needs to be welded up, and also 3 oil returns dont line up, need to modify the head aswell to compensate

MYRB30 Rising Star

MYRB30

Posted
Posted

Its too hard to fit oil jets to a RB30, I know of one shop that used five blocks before he found one that could take all size jets. The sand cast blocks of the RB30 was just to inconsistant with its core shift during casting for consistant fitting of the jets

VB- Veteran

VB-

Posted
Posted
alrite bud, you know everything

dont take it to heart mate, just saying, there are plenty of high powered RB30's out there, and its alot of work to get the RD28 block going with the 3 litre innards. i havent really heard of RB30 blocks letting go, bar those extreme cases of problems (tuning, oil contro, whatever), or extreme horsepower, but even with the latter there isnt an abudance of supporting evidence, not that i've seen anyway

  • 2 weeks later...
richie$$$rich Contributor

richie$$$rich

Posted
Posted

A friend of mine has a 25/30 setup.

Spec's are as follows,

STD Series 2 Block

STD rods and pistons (Motor has not been apart since god know's when)

RB25 head

STD Head ports

STD intake manifold

set of small cams

STD rb25 EX manifold

GT3540 0.86 rear

Haltech e11v2

044 pump

STD R33 box

H/D clutch

made 480HP on 20PSI pump fuel

Daily drive for the last 2 years @ 20psi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • luke gtr
      Hiya!

      By luke gtr · Posted

      Welcome.  800hp should be a bit of weekend fun!
    • Kinkstaah
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Kinkstaah · Posted

      I'm going with "Just run two gates". Fix the problem conclusively. It's the only way you'd ever truly know, right?. This is all pretty much splitting hairs. Even the extreme example where it takes two whole seconds at 100kmh or something sounds monstrously dubious. And anyway, when you're punching the throttle when you 'need' this power, you aren't at 2800rpm in the wrong gear. Test it at 5600rpm in 3rd gear, when you're traction limited punching out of a sweeper. Much difference there when you account for traction?
    • GTSBoy
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By GTSBoy · Posted

      And the full R32 GTR wiring diagrams are also freely available. Hmm.... there's supposed to be an auto replace that would have linked the thread. Here it is, manually  
    • dbm7
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By dbm7 · Posted

      Ahh...should have been clearer ~ there's 2 ... SMJ = super multi junction (connector)...   ...this is connector 6 & 25 in above image -- body harness to engine loom (6) & body harness to main loom (25) Headlights go to front via connector 6 ; fuel gauge goes to tank sender via connector 25  ...like I say this is R33 diagrams, but at a pinch R34 won't be too far different. *IF* the two ground faults are related, this can be the only place where both wires converge (as one runs to the back, the other to the front)... ....thing is, you probably need to establish if the faults are related (unless you examine that area and find obvious chaffing on the looms there to body ground)....*IF* the fuel gauge is still broken (full needle deflection), I'd be headed for the boot, remove fuel sender wire, key on and measure the voltage there ~ it should be roughly 10volts. If that's ok, check sender to ground resistance...if this is a dead short to ground (and there's fuel in it), then sender has failed or something funky has happened to wiring in the tank. edit: ahh...rereading the thread, this is R32....above fuel sender test still valid tho'
    • drifter17a
      Rb25det timing belt position on cam gear

      By drifter17a · Posted

      I just changed the timing belt on my RB25DET NEO and wanted to get some opinions. I’ve been super cautious, did a lot of research, and took my time. I’ve driven the car, and it runs fine. After warming it up, I revved it to 8000 RPM a few times—no issues, everything held up.   After the drive, I heard a noise that I think is either the clutch or possibly a tight accessory belt. It’s not constant, just comes and goes.   I took the timing cover off to double-check everything:   Belt is on properly, Tensioner is tight, Did the 90-degree twist test—belt isn’t too tight or too loose.     What still worries me is that I noticed the belt seems to sit a little toward the front edge of the gears, especially on the idler pulley. It even looks like it’s slightly coming off the edge there. Is that normal?   My old belt (5 years old, ~3,000 miles) also showed a bit of wear on that same edge, so maybe it’s just how it sits? I’m probably overthinking this, but since it’s my first time doing this on a NEO and the engine is forged, I really don’t want to mess anything up.   Also, I’m thinking of swapping to a clear front timing cover with the glass window. Would you recommend NITO or HPI? HPI looks reputable and their covers have 2.5mm thickness, but not sure if there’s a real difference between the two.   Any advice or reassurance would be much appreciated!
×
×
  • Create New...