Jump to content
SAU Community

Clutch Pedal Gone All Of A Sudden Whilst Driving ...

BLK33T
 Share

Recommended Posts

BLK33T Community Regular

BLK33T

Posted
Posted

Clutch pedal gone all of a sudden whilst driving ...

Hey,

I was driving along yesterday and went to change from 2nd to 3rd when the clutch pedal just seemed to fall to the floor. Now when I push the clutch pedal down it doesn't disengage the clutch properly. I have to push the pedal as hard as i can to get the car into gear and to get it home i had to blip the rev in between shift so that it wouldn't crunch gears. It's going to Bezerkly tomorrow to get checked out just wondering if anyone could give me an idea of whats going on cause its doing my head in...

Thanks :nyaanyaa:

chiksluvit Experienced

chiksluvit

Posted
Posted
Clutch pedal gone all of a sudden whilst driving ...

Hey,

I was driving along yesterday and went to change from 2nd to 3rd when the clutch pedal just seemed to fall to the floor. Now when I push the clutch pedal down it doesn't disengage the clutch properly. I have to push the pedal as hard as i can to get the car into gear and to get it home i had to blip the rev in between shift so that it wouldn't crunch gears. It's going to Bezerkly tomorrow to get checked out just wondering if anyone could give me an idea of whats going on cause its doing my head in...

Thanks :nyaanyaa:

most likely your clutch master cyl is gone

change the slave cyl as well if you're doing the master cylinder

check your clutch fluid level, if it's too low then top it up, pump the pedal up and drive it carefully to the mechanics to get it fixed

the genuine master and slave cylinders aren't that expensive from nissan, so just save yourself the hassle and get new ones instead of messing around trying to rebuild/reseal the master cyl.. if the master cyl bore is scored then u've wasted your time rebuilding it

zebra Grand Master

zebra

Posted
Posted

I Wish I had an easy fix like that :(

Just Pulled my slave off to change as I thought it had gone only to find that the locating/pivot bolt for the clutch fork has snapped...Yay Gearbox has to come out now :)

chiksluvit Experienced

chiksluvit

Posted
Posted

speaking of spot welds on the pedal brackets..

this reminded me that few days ago when my friend's r33 got broken into when parked on the streets in redfern/waterloo area

nothing was stolen, all they did was they pulled the brackets out of the accelerator pedal

and punctured one rear tyre..

when i saw it i was surprised how it didnt seem too hard to pull the bracket out... done with just a bit of leverage, force wasnt even enough to bend the bracket

with clutch pedal being heavier than accelerator, especially if you have heavy duty clutch, i guess it'll become a weak point..

chiksluvit Experienced

chiksluvit

Posted
Posted
why would they pull the accelerator pedal box out?

that is quite random! :thumbsup:

ya it is

and popped one of the tyres too

the parking spots close to city, on the streets, in front of some houses..

they probably didnt like him parking there so decided to do something to his car so he won't park there

whoever did it knew skylines quite well by the way it was broken into...

THENIG Community Regular

THENIG

Posted
Posted
I Wish I had an easy fix like that :P

Just Pulled my slave off to change as I thought it had gone only to find that the locating/pivot bolt for the clutch fork has snapped...Yay Gearbox has to come out now :D

Same thing happened to my friend last weekend at DECA in Shepparton, had to drive it back to melbourne with no clutch starting it in gear. Do you know if there's anything that gets left inside the box that could be left dangling and doing damage to the inside of the gearbox?? Sorry don't mean to hijack thread..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      @soviet_merlin Thanks mate!  Nothing too major but will hold me up for a while. I've got lymphomas to get taken off the back of my neck and the middle of my spine which always conjures scary thoughts!  It sounds worse than it is. Yeah great, conjuring more rabbit hole deepening , just what I need! 🤣  
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      I'd argue the F50 kit I got is very good value. For ~2k I got the calipers (refurbed condition), adapters, pads, brake lines, rotors, and top hats. I think you'd be pretty hard to get Evo/GTR/350z brembos + the additional hardware for similar money. Used market for a pair of front calipers alone I've seen tend to run anywhere from $1500-2000 depending on condition.    That said, something like a GTR or 350z brembo is a lot easier to adapt to the Silvia. 
    • Milkmun
      S15 Spec R

      By Milkmun · Posted

      Is there a significant price difference between the Evo/gtr/350z brembos vs the F50? Looks amazing.
    • Dose Pipe Sutututu
      R33 fuel setup

      By Dose Pipe Sutututu · Posted

      I was actually being a tightarse at the time LOL... My OCD is tickling me into running a 2nd 8AN Teflon hose all the way down and removing the 2x OEM hardlines. My other side of my brain is telling me to run 2x hardlines front to back (also acts as a fuel cooler, so win win).
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As I mentioned in an earlier post, I had some trouble with the Silvia's brakes dragging back in 2023. I managed to sort it out then, but the same problem came back to bite me late last year. Just take a look at the picture – I had a feeling the handbrake was acting up again, and I was right. Anyway, I'd been wanting to upgrade to bigger brakes for a while. Not that the Silvia's brakes were bad, but it was more of a "want" than a "need", you know? It was funny, though – at the time, I couldn't find any Evo Brembos, 350Z Brembos, or GTR Brembos for a decent price (of course, tons of them popped up online after I already bought my kit!). I ended up going with an F50 Brembo kit, which came with adapters, brake lines, 330mm rotors, and top hats. The F50 Brembo caliper was used in a few other cars too, like the FPV. I also decided this was the perfect opportunity to ditch the Silvia's ridiculous rear brakes and that awful handbrake (some of you were definitely right about that!). I picked up some R33 calipers and all the necessary bits – rear drums, backing plates, and new hardware to refurbish the calipers. Of course, it wouldn't be a project without a few hiccups. Turns out the brake master cylinder was playing up and basically (to put it simply) keeping the brakes engaged. I had it overhauled, and after some adjustments, everything was working again. The whole process took a while, as you can imagine. To top it off, the front right wheel bearings were shot and needed replacing too. This is a rare occasion where I'm posting an update while it's all still fresh! These pictures were taken just this afternoon.
×
×
  • Create New...