Jump to content
SAU Community

Recommended Posts

Guest Robo's

This is the first car i have had with severe oversteer. I want to reduce it!!

Its got Tein NR suspension, rides very firm, i feel this maybe the cause. Also 17*9 at the rears with 255/40/17 which mean it should hang on, but it doesnt, any good throttle will send the rear out, i might try reducing the back tyre pressures to reduce it.

Anyone elses opinion.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/
Share on other sites

you only reduce ur tyre pressure if you, say driving a 4WD on a sandy beach so your tyre didn't sink.

Or, you go to drag race and need a little tyre wall flex so you get more grip on hard (straight) launch, not just bumping around the track.

For anything else, pump up your tyres with enough pressure in it, coz they're good for corner handling and less rolling resistance will save fuel.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-462741
Share on other sites

youll need to do some more research. My konis are adjustable, but you have to remove the shock, fully compress it, and rotate the rod to adjust the damping, there are no external adjusters so they dont LOOK adjustable.

Maybe have a look at your rear camber, and make sure there is no rear toe out as previously suggested. Might have excessive rear camber.

I would even take it to a suspension specialist, get them to look at all the suspension mods and alignment, then drive the car, and work from there.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-463585
Share on other sites

I've got the whiteline kit with adjustable sway bars, front on hard and the rear in the middle. still find that on fast tight corners (eg turning right at lights at around 60, no traffic around!) it has a tendency to understeer just a little, but then to flip into oversteer without much/any warning. can be rather scary and hard to correct, to the point that i have a little less confidence in the car's handling than i feel i should. the rear end is far less "twitchy" than a lot of rwd cars i have driven, but the way it can just snap out on you with no warning worries me.

Question, i guess, is should i try full soft at the rear sway? the shocks are bilstein all round but not adjustable

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-478845
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia body...
    • This. A 3d wheel alignment is like $120...just take it to the shop. Since theres probably multiple adjustments that need to be made after changing something. Mine has front/rear lower arms, traction rods, tension rods, camber arms, toe arms, front upper arms, hicas kit, sway bars and coilovers. I measure from the edge of the bolt holes on the originals and set the same length on all the adjustable stuff to dial it as close as I could to OEM. Took it straight for alignment; it didnt feel right at all...after alignment, it feels perfect. Similarly i've just changed the springs on another car; and I still needed multiple adjustments to bring it back in spec.
    • A full Veilside kitted JZA80 Supra in Meriken park in Kobe city a few weeks back
×
×
  • Create New...