Jump to content
SAU Community

Recommended Posts

Guest Robo's

This is the first car i have had with severe oversteer. I want to reduce it!!

Its got Tein NR suspension, rides very firm, i feel this maybe the cause. Also 17*9 at the rears with 255/40/17 which mean it should hang on, but it doesnt, any good throttle will send the rear out, i might try reducing the back tyre pressures to reduce it.

Anyone elses opinion.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/
Share on other sites

you only reduce ur tyre pressure if you, say driving a 4WD on a sandy beach so your tyre didn't sink.

Or, you go to drag race and need a little tyre wall flex so you get more grip on hard (straight) launch, not just bumping around the track.

For anything else, pump up your tyres with enough pressure in it, coz they're good for corner handling and less rolling resistance will save fuel.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-462741
Share on other sites

youll need to do some more research. My konis are adjustable, but you have to remove the shock, fully compress it, and rotate the rod to adjust the damping, there are no external adjusters so they dont LOOK adjustable.

Maybe have a look at your rear camber, and make sure there is no rear toe out as previously suggested. Might have excessive rear camber.

I would even take it to a suspension specialist, get them to look at all the suspension mods and alignment, then drive the car, and work from there.

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-463585
Share on other sites

I've got the whiteline kit with adjustable sway bars, front on hard and the rear in the middle. still find that on fast tight corners (eg turning right at lights at around 60, no traffic around!) it has a tendency to understeer just a little, but then to flip into oversteer without much/any warning. can be rather scary and hard to correct, to the point that i have a little less confidence in the car's handling than i feel i should. the rear end is far less "twitchy" than a lot of rwd cars i have driven, but the way it can just snap out on you with no warning worries me.

Question, i guess, is should i try full soft at the rear sway? the shocks are bilstein all round but not adjustable

Link to comment
https://www.sau.com.au/forums/topic/21783-r33-oversteer/#findComment-478845
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
×
×
  • Create New...