Jump to content
SAU Community

Recommended Posts

Guest TR34GT

Hi SAU members.

I have been experiencing another, and an unusal problem.

It's a one problem after another and fix them as I go.

In the end, I hope I'm left with a car that is 100%. Nearly there hopefully.

On the weekend, I was coming back from mums place late one night, and at a set of lights where I was turning right, I floored it, and after taking the corner and accelerating in a straight line, the AT light came on in the dash.

I immediately lost 1st, 2nd and 4th gears! OMG

I limped home, but made it the 20km and pulled into the driveway.

I switched off the ignition, and after the TT shut down, I counted 15 seconds, then re-fired up the ignition.

The AT alert light was off, and I had my gears back.

The car ran smoothly and the tiptronic and full-auto worked fine for the rest of the weekend.

It's now monday morning and I'm doing 130km/hour up the F3, and the light comes on again.

I immediately lost 1st, 2nd and 4th gears once again.

I waited till I got to the Hawkesbury River turn off, then pulled over and shut down.

After re-starting, sure enough, the AT light was off, and the transmission appeared to re-set.

I drove into work slowly along the old road, without problems.

Is anyone else experiencing this problem?

Please let me know.

Many thanks.

TR34GT (Jim)

ps............Car Care Data Sheet 4 attached

CDS_No_4___Tiptronic_Transmission_Light_at_High_Speeds.pdf

Edited by TR34GT
Link to comment
https://www.sau.com.au/forums/topic/217923-r34-tiptronic-transmission-problems/
Share on other sites

  • Replies 128
  • Created
  • Last Reply

Top Posters In This Topic

Guest TR34GT

Colosus.

Thanks for the vote of confidence on my technical ability. LMAO j/k

Yep. Check it once a week.

All has been good so far.

Chook,

Yep. Wyong Automatics are running the diagnostics on the error codes tomorrow morning

No trouble at all coming home this afternoon.

I hate intermittent problems.

Thanks for your help guys.

I'll let you know the outcome, and write up a Car Care Data Sheet.

Regards

TR34GT (Jim)

Guest TR34GT

Ok. No luck here.

The automatics specialist says that the R34 GTT does not retain the error logs for the tiptronic transmission.

Go figure. Are they having me on?

They stated that the only way that I can tell whats happening is bring the car in for a diagnostic, with the problem occuring.

(thats a bit hard when it only happens once in a blue moon)

Any ideas ?

It does retain error codes, run it yourself : http://www.skylinesaustralia.com/forums/in...t&p=3605428

quite tricky to activate the diagnostic mode, takes a few attempts to get it right.

possible a shift solenoid by the sound of it ??

Guest TR34GT
with the 33 auto if you unplug the brown electrical plug near your drivers headlight it will lock the trans in 3rd so 1 2 4 wont work

\have a look if you have a big brown plug near your headlight

Geezus wept. That came out from left field.

I'll look. So you are saying that it may be a loose brown wire there, if the 34 is the same as the 33 wiring?

I'll give it a go.

Thanks dangerman4.

ps................the problem hasn't re-ocurred since Tuesday, and I have well and truely been trying to make it happen. And ps again

Guest TR34GT
It does retain error codes, run it yourself : http://www.skylinesaustralia.com/forums/in...t&p=3605428

quite tricky to activate the diagnostic mode, takes a few attempts to get it right.

possible a shift solenoid by the sound of it ??

Many thanks Chook.

It may be that the transmission exoerts don't know how to interface their gear with this particular car.

He said his gear reads only 80% of the computers in various makes and models.

Looks like its time for a new mechanic.

I'll keep trying.

Thanks again.

TR34GT (Jim)

Guest TR34GT
100% Shift solenoids, get them both changed (A + B) while your car still at least lets you use the other gears and reset the box.

It'll eventually lock you in 3rd forever!!!!

Many thanks 666DAN.

I take it this has happened to you before?

I'll ask the autotrans guys to change them.

Regards. TR34GT (Jim)

  • 1 month later...
Many thanks 666DAN.

I take it this has happened to you before?

I'll ask the autotrans guys to change them.

Regards. TR34GT (Jim)

hey there sounds exactly like wat im having

but i have already got it stack in 3rd only all the time now

have u changed them solenoids and did it fix it 100%

let me know cheers

hey there sounds exactly like wat im having

but i have already got it stack in 3rd only all the time now

have u changed them solenoids and did it fix it 100%

let me know cheers

Yep it fixed it 100% it's an annoying fault to find as when the solenoids are room temp, they test OK...it's only when you heat them up that you find they have gone open circuit. Change them both and never worry about it again :D

i had the same experience in my other car (mazda6). turned out to be low voltage from the stuffed alternator. sticking in 3rd was the cars "limp home mode". new alternator and no more problem, but a different car, might be related though.

i know its not the same car but in my nc fairlane i had the same thing, i was told when that happens the auto ecu has put its self in limp mode, it only happened once and when i turned it off and re-started it there was not a problem.

Yep it fixed it 100% it's an annoying fault to find as when the solenoids are room temp, they test OK...it's only when you heat them up that you find they have gone open circuit. Change them both and never worry about it again ;)

Hi Guys, sounds exactly like my problem, my mechanic found error codes 10 -vehicle speed sensor, 12 & 13 solenoids A & B. I was just about to order a new speed sensor as they said this would be the problem because it was the first error, glad I read this first. Mine started happening after a nice little fishy round a corner about a month ago, now whenever I pull up going down a hill it goes in 3rd until I turnoff and start again. I have noticed if I use manual mode from the start I can stop it from happening so until I get the solenoids changed I'll keep using manual.

Thanks 666Dan for saving me a speed sensor that is probably fine :D

Mine puts the at light on if I give it some in the rain or on the burnout pad at the drags

but goes out as soon as the speed drops below 5 Km/h

been doing that for over 2 years now

never been stuck in 3rd gear after doing that

only when I installed the Emanage one day it stayed on 3rd

Mine puts the at light on if I give it some in the rain or on the burnout pad at the drags

but goes out as soon as the speed drops below 5 Km/h

been doing that for over 2 years now

never been stuck in 3rd gear after doing that

only when I installed the Emanage one day it stayed on 3rd

mine does the same thing occasinally when i slide abit in the rain etc.......i thought it might be normal! i guess not

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yuck. But it's kinda the same principle, moving timing around to make car run bad but sound good.... I went for a more spirited tuning drive to iron out a few things. Car no longer stalls, and it loved to dip RPM low when you clutch in. After tuning this (and the 4-5 tables that HPTuners/LS1 OEM ECU wants for idle air correction) it's now behaving somewhat normal. All expected because there's a new TB, new Intake manifold and that new TB which is 102mm vs 78... has an entirely different IAC passage which is smaller because ????? Unfortunately at this point I went to make further fine tuning changes to avoid it flaring up, you know... _tuning_ the HPTuners dongle died. Well to be more accurate - The USB cable died in a fashion that anyone who has ever charged a phone will recognize. After the app demanding I resync it 50 or so times (which all 'succeeded' but all failed) the device does not want to sync and I've logged a ticket with support to see if it's fixable. US Support said it was a 'storage issue' but after removing the SD card inside it and formatting it/fixing it the issue does persist. Unfortunately usually the fix is "Turn in your old dongle and pay $700 for the upgraded one" it's cheaper because I get some free licence credits I unfortunately don't need. However I'm 10 minutes down the road from HP Tuners AUS/VCM so at least I won't need to post it, and logged a new ticket for support over here. Definitely drives different. My SOTP dyno believes it's probably making 310-320kw instead of the 280 before.  It scrambles for traction a little now whereas it previously different. It drives like a bigger cam car up top even though the cam is smaller, likely due to the cam not being advanced 6 degrees. The timing is deliberately low and the fuel is very rich so who knows if this will improve on the dyno. It may, imperceptably. Also funny is removing the pineapples definitely makes the car squat more and axle tramp less. So this behavior of having more top end, squatting more, and scrabbling for traction more makes me think = more power. But I could have just been sitting on the threshold of that kind of behavior before. Time will tell if my butt dyno is calibrated right. I need the exhaust leaks fixed before dyno tune for obvious AFR related reasons - I repositioned the pipes but I'm not confident it's fully sealed even if it is better. At least the car does drive around while I cannot tweak/tune it for now. And I have aircon again. medium success!
    • Don't use that manifold. Please don't use that manifold. Sunk cost fallacy is not worth the later pain. None of these will be relevant to the change that will come from the different turbo and manifold. As in, the effect of the exhaust will be nil, regardless of what else is changed. And all the cam and fuel system stuff is not changing either way, so has no effect. The turbo and manifold (and to a small extent the wastegate)....big change.
    • Just wanted to say thank you for your input   my man (lead mechanic by trade) and I have done a heap of work as you can imagine just to make the hot side work with the dump pipe, stupid massive intake on turbo, trying to get the waste gate on was not fun.  I’m kinda getting to the point where I don’t know if I try and make this work and not throw all this cash and time away or do I scrap the lot and start again? the Apexi I’ve got was tuned for a few slight differences:   Tomei pon cams (mine are stock neo) Turbo smart 38mm external waste gate (mines 45mm replumbed) with stainless screamer pipe  3inch turbo back exhaust with high flow cat Sard 800cc top feed injectors Sard adjustable fuel pressure reg    
    • Out here E90s are the cheapest way into a sporty-ish car because everyone knows just how expensive the repairs can get. 8-10k USD for an automatic 335i. 
×
×
  • Create New...