Jump to content
SAU Community

Recommended Posts

hey guys

As some of you may have already seen i am putting in a rb25 in my 32 with in the month or so.... now i am in the process of find who could help us out in fitting it for me as i am no where near qualified and i would want it done right haha

so if any knows of a good person/workshop to go to... or a place where you have been and wish to recommend, this would be greatly appreciated

thanks :blush:

Edited by wellzy
Link to comment
https://www.sau.com.au/forums/topic/218701-rb25-halfcut/
Share on other sites

just found invoice

rb25motor and box: $3460

microtech lt10 ecu: $1320

hd organic clutch: $630

3 inch dump: $360

mufflers removed, micro tech wired in, box and motor install, clutch installed, removal of rb20det, dyno tuned: $ 900

pluss 667$ gst

made 250hp at 13psi

Link to comment
https://www.sau.com.au/forums/topic/218701-rb25-halfcut/#findComment-3857817
Share on other sites

just found invoice

rb25motor and box: $3460

microtech lt10 ecu: $1320

hd organic clutch: $630

3 inch dump: $360

mufflers removed, micro tech wired in, box and motor install, clutch installed, removal of rb20det, dyno tuned: $ 900

pluss 667$ gst

made 250hp at 13psi

thanks champ.... that helps me heaps

keep em coming guys :blush:

Link to comment
https://www.sau.com.au/forums/topic/218701-rb25-halfcut/#findComment-3857899
Share on other sites

thanks for all the replys guys.... i will be contacting all of them and getting an idea of pricing...

im also thinking about asking ovaboost in malaga and kensei garage in wangara as i have dealt with them b4.... so ill see how we go, ill keep yous all posted

thanks again

Link to comment
https://www.sau.com.au/forums/topic/218701-rb25-halfcut/#findComment-3866369
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Of course you can. That was a waste. Straight down one oil drain gallery and out the sump hole. Could at least have run the engine a little (obviously with at least minimum oil level on the stick).
    • Oh really? Maybe I'm being silly. I'll get some more shots. I had it higher but found that it went too high after a drive, I never knew this but exhausts can move around a bit when hot (makes sense, just never knew) and when it was higher it would make nice cooking plastic smells. That said, I could put some heat tape on a'la 90's R33 exhausts     Ha, I've spent a lot of my life in castle hill waiting for cars to be done. I think I'd prefer something closer but thanks D. 
    • @Duncan Yes, changed filter every time. I don't have the service manual for the car yet (Car was imported and they removed everything when importing). I've been using the oil change threads in the forum as reference.   @Milkmun The second oil change was after ~4 months after the first months and I wasn't sure about reusing engine oil that was opened. The third oil change happened within 3 weeks of the second oil change and I used the previous leftover oil to just "clean up" the system. (Poured it through while the sump plug was open")
    • I left the ceramic coating off this bit, hopefully it just comes off after a few drives.   The gap between the spokes is too tight for anything on a stick, its only marginally bigger than my finger. I have to use a brush to get in there and its a big reason why I thought I'd try the coating.   Absolutely will do. I have EBC Blue Stuff pads to put on the front which will make them a bit dirtier. I'm hoping a pressure wash will just get most off. The shine is different to most, its very thin but seems very well 'attached' so hopefully it lasts.   
×
×
  • Create New...