Jump to content
SAU Community

Recommended Posts

Hi all,

I've got a R33 non-turbo. I've problems with the gearbox. I can hear a loud crunching noise when shifting from 1st to 2nd. And, also the reverse gear is hard to select. Can i have just these fixed or do I need to recondition the gearbox? And, also at what figure am I looking to get it fixed? Any recommendations highly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/219449-gearbox-reconditioning/
Share on other sites

Shell Spirax CX 80w-90 is recommended (by nissan and they recomended it 15 years ag for r33's so do not use is same for castrol with the nulon adjective is not good its not capable of the gearboxes needs the syncro's with get crused

cross reference this with a redline oil and its a smoother oil and you will thank yourself for paying a little bit more :D

I've done some searching because i'll be doing 'box oil soon. A quick search in SAU says Redline Lightweight XXXX (forgot exactly) is the way to go. There's a few different grades, so do some research before you pick one. It's blue coloured.

My gearbox is rough too. It's not cheap ($3000 new box) to either reco OR replace it so try avoid it unless you have lots of cash :thumbsup:

R338OY is right about the oils :thumbsup:

the make of the oil is called redline lightweight shockproof

the grade is up to you depending on the crunch, when you go to the place take a look at the grades they sell in that type of redline try somthing close to a 80w-90 as i see a lot of skyline guys using that grade. Remember winter is coming up too and the crunch may seem worse so give the gearbox about 500-1000km to get the oil through its system (ive read on the forums the guys say the any gearbox oil needs to coat it for a bit)

around what area are you in?

im on the central coast N.S.W and i guy mine from Bursons automotive

again prices range and i see it inbetween $25 and $33 per liter

i dont know how to fill the gts people say pour it down the shifter and others say that dosnt go to your gearbox so look into that.

i have a gts4 so i have to use a handpump to put my gearbox oil in

cheers, Andrew

MELBOURNE — A-car Accessories

Contact Name:

Chris

Phone: 03 9639 8393

Fax: 03 9639 8016

Address:

231 Russell Street

MELBOURNE, 3000, VIC

Email: Pls phone

Speciality: Red Line Oils & Autoparts Retailer

Try there first people to look apparently its slightly cheaper if not you will find bursons stock a good range of redline.

gts4 mayyybe a little different, mine is 3.8

if anything yours will be less but not by much only 200ml

  • 1 month later...

Boys Redline is One of the worst things you can run in your gearbox

Only Mineral oil in the box (for eg. Castrol VMX 80)

redline will only wear out the synco more.

it is only a bandaid fix for maximum 1000km...............

If hear crunching........ that means that you syncros are lazy

meaning a recondition is need..............

I know it should cost About $1000-$1500 from Craft differenitials :D

No its not lol we use redline in all our rebuilt gearboxes in high hp cars like gtr etc,

we swear by the stuff .

it sounds to me more like this guy has a clutch drag or the bush in the crank , as reverse doesnt even have a syncro,

ide be checking the adjustment of your clutch if it engages close to the floor then adjust it so its engages about half way along the pedal stroke, and i reckon that will help it to ,

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey y'all! I'm curious about how y'all go about widebodying your cars. I noticed that when running a square setup, my front wheels are a bit more tucked in than my rear wheels. Not by much, maybe 5-10mm. This leads me to wonder - when I widebody, should I use narrower front flares and wider rear flares? I found a set of 40mm rear flares that I really like, and was thinking of pairing them with some 18mm front flares, but I don't want the car to look strange. How have others done this? Note, I'm in a sedan. Thanks!
    • And if it was anything other than an auto tranny part, it might be a problem. But seeing as all auto trannies belong in the recycling bin, it's fine.
    • I have an R32 Fenix rad. It is good.
    • All the schemas I can see, indicate your typical setup of ATF 'cooler' (read: heat exchanger) in the bottom radiator tank..ie; https://nissan.epc-data.com/stagea/wgnc34/5413-rb25det/engine/214/ ...but I can prattle on a bit here. These trannies have a thermistor in the sump ~ the TCU reads this and 1. bumps the line pressure up when the ATF is 'cold' and 2. prevents the TC lockup clutch from operating, until the ATF comes up to minimum operating temp (keeps the ATF 'churning' through the TC so it heats up quicker) -- trigger point is around 55C. In these conditions, the engine coolant temperature rises faster than the ATF temperature, and also helps heat the ATF up, which is why it's best to think of the in radiator tank setup as a heat exchanger ; the heat can flow in both directions... ...with these trannies, the 'hot' ATF comes out the front banjo bolt, flows through the cooler/heat exchanger, and returns to the box  via the rear banjo bolt. This gets a mention, due to the wildly different opinions wrt running auto trans fluid coolers ~ do you bypass the in radiator tank altogether, or put the cooler inline with the in radiator tank system...and then, do you put the additional cooler before of after the in radiator tank system?... ....fact is the nominal engine operating temp (roughly 75C), happens to be the ideal temperature for the ATF used in these trannies as well (no surprises there), so for the in radiator tank system to actually 'cool' the ATF, the ATF temp has to be hotter than that...lets say 100C -- you've got 25C of 'excess' heat, (slowly) pumping into the 75C coolant. This part of the equation changes drastically, when you've got 100C ATF flowing through an air cooled radiator ; you can move a lot more excess heat, faster ~ it is possible to cool the ATF 'too much' as it were...(climate matters a lot)... ...in an 'ideal' setup, what you're really trying to control here, is flash heating of the ATF, primarily produced by the TC interface. In a perfect world, wrt auto trans oil cooling, you want a dedicated trans cooler with builtin thermostatic valving - they exist. These should be run inline and before the in radiator tank system ~ when 'cold' the valving bypasses the fin stack, allowing the ATF to flow direct to the in radiator tank heat exchanger, so it works 'as intended' with helping heat the ATF up. When 'hot' (iirc it was 50C threshold), the valving shuts forcing the ATF through the cooler fin stack, and onto the in radiator tank heat exchanger...and you sort of think of it as a 'thermal conditioner' of sorts...ie; if you did cool your ATF down to 65C, the coolant will add a little heat, otherwise it works as intended... ...the 'hot' ATF coming from the front bango bolt, is instantiated from the TC when in use, so all/any flash heated oil, flows to the fluid-to-air cooler first, and because of the greater heat differential, you can get rid of this heat fast. Just how big (BTU/h) this cooler needs to be to effectively dissipate this TC flash heat, is the charm...too many variables to discuss here, but I just wanted to point out the nitty-gritty of automatic trans fluid coolers ~ they're a different beastie to what most ppl think of when considering an 'oil cooler'... /3.5cents   
    • Been a busy but productive day. Axle and hubs acquired. All fitted up after a bit of modifying. Need to sort out wider mudguards and running light reflector covers but other than that the trailer is gooood to go !!
×
×
  • Create New...