Jump to content
SAU Community

19" Roh Drift R's


Recommended Posts

As title says I have a set of 19" ROH drift R's to get rid off they are in good nick. There is one small mark on one of the rear rims and a mark on the inside of one of the fronts (I don't know how that got there :down: ). One of the rears is missing the R badge from the centre cap.

They have Hankook K104's on all four corners, both fronts have about 80-90% of the tread left and the rears have about 10% before they hit the wear indicators.

The rims are about 3-4 years old.

They measure 8.5 inches at the front and 9.5 at the rear. They were ordered with the offset to suit a R33 GTST, I can’t find the off set printed any where on the back of the rim. They fitted my car which has a wheel centre to guard height of 350mm and a camber kit on the front and rear, Both front and rear guards had to be rolled once the camber kits where installed.

I am located in the Hunter Valley N.S.W, feel free to PM me or post at will.

I am asking $1200.00 ono

:wub:

Ryan

post-14375-1210921164_thumb.jpg

post-14375-1210921232_thumb.jpg

post-14375-1210921263_thumb.jpg

post-14375-1210921302_thumb.jpg

post-14375-1210921453_thumb.jpg

post-14375-1210921483_thumb.jpg

Link to comment
Share on other sites

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...