Jump to content
SAU Community

Recommended Posts

ok, i searched for some other threads though i thought id post another since my symptoms are a little different. it seems when i get up near 90kmh or faster, theres a shuddering in the steering wheel. it seems to be temperature related too? if you get up to 90kmh within 15 mins or so of starting the car from cold, the shudder is there, but once the car has been warmed up for a while, it goes away. since the car will be going in for a big service soon i figure i should compile a list of things to check through

dont worry sounds the same as mine

all i need is a wheel balance and alignments those are what i have been told it is (professional mechanic guy for rims and alignments and balancing drove it and its been conformed)

so id say 99.9% sure :D

I will be interested to see how you go with this as sounds similar to a problem I have had for the last 3 years - tried wheel balancing and alignments (at both tyre places and professional suspension places) plus put in a castor kit (made a difference)

Is worse when colder and seems to disappear after a while

yeh it seems odd, as all the tyres were replaced only 3 months ago, and barely 2000kms at that. the only other thought is something to do with the drivetrain...it definitely goes away once the car is warmed up substantially, so if it was a tyre balancing issue, wouldnt it always be there?

are there any possible issues with bearings, diffs or attessa system warming up?

its not wheel alignment or balancing. I had the same issue. It is the power steering pump and fluid. Seems to be fine once the car has heated up. Check your fluid levels, give it a good flush with some new fluid and take it easy until the car has warmed up.

Just read the stroy in HPI of gtr brake upgrade this is the explanation it gives of brake shudder

Qoute"In a nutshell if your getting feedback through the steering wheel and suspension when you brake at certain speeds and pressures,then you are experiancing what is known as brake shudder,This feedback can range from a faint vibration that is barely noticeable,to a series of shakes that are so bad they feel violent enough to almost rip the wheel from your hands. It doesnt matter if your on the track or the street,because it is caused by an uneven build up of pad materieal on the surface of the rotors. It is agrrravated by the high temps of the track and by the switching back and forth between two incompatible friction materials. It should also be pointed out that the shudder is the result of a thickness variation in pad build up on the rotor surface and not the popular myth that it is caused by warped rotors."end quote

Hope this helps somewhat there is also a very good guide to bedding in brakes and pads but to much for me to re-type here i suggest everyone grabs a copy and has a read for themselves some very good info in there. The article also gives Hawk pads the big thumbs up for pads i read somewhere else on these forums that they make str8 swap pads for stageas so this may be of note to those needing to upgrade soon.

Hope this helps somewhat there is also a very good guide to bedding in brakes and pads but to much for me to re-type here i suggest everyone grabs a copy and has a read for themselves some very good info in there. The article also gives Hawk pads the big thumbs up for pads i read somewhere else on these forums that they make str8 swap pads for stageas so this may be of note to those needing to upgrade soon.

LOL

just be aware that there are a couple of skyline owners (and a 350Z owner) that are too paranoid to brake near a cop car, using those Hawk pads, as they increase brake noise a LOT.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • https://www.efisolutions.com.au/coolant-temperature-sensor-bosch-180sx-s14-s15-r33?gad_source=1&gclid=CjwKCAjwzMi_BhACEiwAX4YZUHsCQhbiDT_NC3q5wD9jrzH6Dts9eGSr19NXSDw7x9WVm1sH7G3S4hoCwaUQAvD_BwE this is the one i replaced today
    • I have replaced the larger coolant temp sensor, i do see a smaller one next to it (looks to be just 1 pin) but i assume that is just for the dash? or should i replace that aswell?
    • Check coolant temp sensor ~ symptoms fit the hard hot start/cold start OK scenario --- if sensor goes open circuit, ECU thinks engine is cold and enriches mixture ....works when engine cold, but floods them with rich mixture when hot (Hyundi MAP engines are a bit infamous for this)...
    • OK, starter changed for a spare without much trouble. Neil had kindly left space to get to the top starter motor bolt from above with a long spanner which makes the whole deal much easier, and everything else was neat and easy to get at from underneath. Once the starter was changed everything was good, unplugged the CAS and turned the motor on the starter to make sure everything was free and happy. Onto properly priming the oil and first start. I'd picked up one of these oil prime kit from Boost doc a while back and this was my first time using it.  https://boostdoc.com.au/products/engine-oil-prime-kit?_pos=1&_sid=28c628a65&_ss=r While I'd organised all the fittings to hook it up to my GTR (sump plug to -6 feed and -4 T to tap it in and retain the oil pressure gauge, neither suited on this car as the oil pressure needs to T into 1/8 NPT not -4 and the Aeropro sump has some massive drainplug not that factory whatever it is. So, waiting for a couple of fittings, then I'll prime it and do first start, hopefully next weekend. Other than that going well, there is very little stopping a final alignment, tune then shakedown day
    • Also to mention, i just tested the CAS, seems to be working fine, can hear the pulses inbetween 0 and 180 degrees, another mention aswell, when i let the car sit for about a hour today, i went to start it and it almost fired on first crank, then just completely struggled. Could it possibly be blocked injectors?, maybe allowing a little bit of fuel to seep past allowing it it almost start first crank?
×
×
  • Create New...