Jump to content
SAU Community

Recommended Posts

3 is nothing

knock is the engine pinging or detonating etc...

the factory warning is set at 60, which is when the check engine light will flash on the dash...anything up to about 30 is ok. If it starts hitting over 30 you might want to get your tuner to look at the tune...

yeah. The mic can often pic up vibrations (not in the engine) and register high, keep driving and see if it's a once in a while thing or a common happening, if the later go see your tuner.

i got mine tuned by matty spry.

usually max knock i see is 18.

BUT when i redline it or go a tad over redline it shoots up to 60+...and the warning lite goes off, because he set it that way.

now he said "when u reach the redline or go over it the knock will shoot up. ignore it. its normal"

is THIS true?

The old knock reading mines been up to 133 & gets up to about 60 everyday but had ears on it with a knock detector & we hear nothing so yeah mine might registering my dog box or something else so i wouldnt worry about 3 lol. On start up knock may read a little high.

every time i hit limiter knock reads anywhere from 70 - 120. i try to stay off the limiter. Yes it is normal

i got mine tuned by matty spry.

usually max knock i see is 18.

BUT when i redline it or go a tad over redline it shoots up to 60+...and the warning lite goes off, because he set it that way.

now he said "when u reach the redline or go over it the knock will shoot up. ignore it. its normal"

is THIS true?

go near red line in 4th or actually hit the limiter?

maybe the air is getting too hot and it is detonating a bit.

If your hitting the limiter ignore all knock readings from the limiter. remember stock limiter is 6900rpm.

go near red line in 4th or actually hit the limiter?

maybe the air is getting too hot and it is detonating a bit.

If your hitting the limiter ignore all knock readings from the limiter. remember stock limiter is 6900rpm.

when i reach limiter man. ahhh, well my limiter is set to 7300. that might be the problem. i will just need to hold back.

Hey guys, i wanted to set the rev cut to 7500 on mine, currently its at 8000.....how can i set it to 7500 on my hand commander, my tuner told me its really easy and somethingi can set up myself.

Also, i didnt know what it was set at before, and i was driving it hard once, and the car kind of jerked really badly (after going high reves, possible over 8000), was that my rev cut doing this, is it safe to hit rev cut...i guess its better than going over the rev i guess.......

Thanks:)

go to settings, then scroll to the last option which is rev. then hit the right arrow so the revs are highlighted then hit down arrow till it's down to what you want. then just hit back and go back to monitor mode or whatever you normally leave it in.

My Mates r33 would contantly register about 80knock on hard driving, the tune was spot on and great. Had a look in his engine bay and his sway bar had a massive dent in it from the intake hitting it, removed it and on full thrash he registered knock of 30. Big change.\

Knock is recorded as any metallic sound as in metal hitting metal, 3 is nothing.

Story pointless just a lil fyi

Edited by DECIM8

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a late reply here as me and my wife have been really busy with new born twins. I finally got these issues fixed and it was something really stupid that caused all of this 🤦‍♂️... After alot of mucking around with trying to figure out what is causing these issues, I back probed one of the R35 coils on the power 12v supply, with the engine running it got 25v! And I thought, hang on..., this isn't normal. Measured my battery with the engine running to check for over charge from the alternator and it wasn't that. So then I dissconnected the R35 PRP coil harness and backprobed the power supply on the engine loom where the ignition coil harness connects, with the key on ignition (engine off) it measured 30v! So then I had to trace where that high voltage was coming from and it lead me to the brown relay "ECM & IGN coil relay" inside the cabin next to the ECU on the passanger wall. This relay feeds power to the ECM and ignition coils. Tried swapping it with another same relay. nah still 30v.. coming from the 2 green/white wires in the brown relay. So then I set my multi meter to the beep continuity mode and probed every fuse on the fuse box inside the cabin to try and find this high voltage power source. Wasn't any of the fuses inside the cabin. Then probed all the fuses in the engine bay and BAM, got my power source that was a 10AMP fuse called "ENG CONT". Pulled the fuse out, and what do you know... it was blown. 🤦‍♂️  So then I quickly replaced it with a new 10AMP fuse, started the car and yeah haha [insert extreme face palm]... The RPM blimping thing went away, car idles smoothly now like what it was before. I swear! I checked all my fuses with my test light twice before I created this forum thread. I think, maybe because one side of that faulty 10A fuse lit up on my test light, I must have thought it was still ok and not blown. But now I know to have both sides light up on the test light when checking fuses... I hate diagnosing electricals.... I'd take mechanical problems over electrical problems any day🤣. Drove the car around my suburb with the engine up to operating temp and it runs fine like before. However, I notice that my fuel pressure is still at 49psi. So I'm thinking this must be normal for my system as I've upgraded the stock fuel pump to a Walbro 255L/h with a constant 12v mod.  But anyway, I'm just glad to have my daily back on the road! Thanks everyone for the replies on this thread, all sorted now! One thing I want to ask you tuner guys, my base fuel pressure on the haltech main settings are set to 43.5psi from default (my tuner must have not checked the fuel pressure maybe when tuning my car?). Do I set it to what it actually is idling on at 49psi? Or just leave it ("if it aint broke, don't fix it/leave it")?  
    • The max they would go for me is 50.
    • That cannot have been a fun set of drilling. The stock "baffle" looks identical to rb26, I just cut fuel cell foam to fit the full length under the baffle.
    • I understand your sarcastic exasperation. But to be fair - the baffles do indeed fit OEM cam covers. They did omit to say that you need to do a bunch of stuff. But they do fit them.
×
×
  • Create New...