Jump to content
SAU Community

Recommended Posts

Since I serviced the 34 on Saturday and hadnt driven it much for a while, I decided to go for a run down to Hobart from home (St Helens) if only to see what the roads are like.

The route along the east coast is brilliant over all, good quality surfaces, a good drivers road suitable for 'interesting' speeds.

There were one or two inexplicable dips in the road on some straight sections that anyone in a really lowered car may come undone on if they're going fast enough though... something to be aware of. The only thing it lacks is a really tight/twisty section - but it has pretty much everything else you could ask for I reckon. Not much traffic at all either.

I didnt spend much time in Hobart itself (drove around Salamanca Place a bit), once I spotted the towers up on My Wellington, I made a beeline for that tower :laugh:

Thats where these pics were taken obviously.

It was freakin' freezing up there (literally) and I certainly wasnt dressed for it either, lol...

Also had a real fun time trying to disarm the immobiliser due to the high RF levels up there, but I perservered!

Came back down and refuelled somewhere close to the city - I spotted one white and one purple (?) R33 in quick sucession but they're the only other Lines I saw the whole day.

It was by then 2PM, so decided better start heading back, so headed up north along the Midland Hwy, made a detour through Richmond, had a look around, then back to the highway north until the Tasman Hwy. 567KM in about 8 hours all up, I didnt see a single patrol car or radar the whole trip either.

gallery_46181_2588_52918.jpg

gallery_46181_2588_16124.jpg

gallery_46181_2588_22026.jpg

gallery_46181_2588_16147.jpg

gallery_46181_2588_6228.jpg

gallery_46181_2588_41850.jpg

Edited by Wayne_J
Link to comment
https://www.sau.com.au/forums/topic/219839-my-st-helens-to-hobart-run/
Share on other sites

Hey man,

Sounds like an awesome day :)

Your car looks friggen sweet as, some nice photos there to :)

Thanks. I really need to plan ahead next time, as once I got to Hobart I had no idea where to go or what to look at, lol.

But going up Mt Wellington was well worth it :)

Next time go from St Helens to Launceston via Scotsdale :) the roads are even better.

Yeah, did that one only a few days after arriving actually... had to go all the way to bloody Westbury just to pick up the cat from the cattery Wridgways decided to use!

As you say its a good drive, on the day I was lucky because once I got that last really windy stretch (just after Scotsdale) there were only 6 slow vehicles all bunched up together, and I managed to pass them all in one go on what was probably the only straight bit of road... gotta love that RB power :)

When I first arrived here, I freaked out a bit about how much loose gravel and stones there seems to be on even the sealed roads (Tasman Hwy in particular).

Was even considering selling the R34 because I know it'd drive me nuts each time theres a new stone chip, but now that I've driven the 3 main routes out of St Helens it doesnt seem as bad as I thought it'd be (or I'm just getting used to it ;)

I just need to keep reminding myself it's only paintwork... the rest of the car will be fine :)

Still, I've never seen so much damned gravel on what are otherwise good roads before, and I've been just about everywhere in Aus and just came from another country area on the mainland. I dunno why they seem to do that here? Case in point was the main road through Fingal, they had just resurfaced the road about 4 weeks ago - and I'm not kidding - they had put at least a 1cm thick layer of loose gravel over the whole stretch. I was driving through there at walking pace, hoping like hell no one would pass me too fast, lol.

Awwwww I miss Tassie for that :) Sounds like a great day!

*glares at Brisbane road surfaces*

I feel for you, I lived in Brissie for a couple of years (2000-2002) and yeah - not many good driving roads around there come to think of it.

You need to go up the coast a bit to around Maleny or maybe south of the border?

If it was a white 33 with gold wheels it was probably me. I was running in my new engine.

Hmm... could've been?

The fuel receipt says I went to BP in Nth Hobart, I saw the white 33 going in the opposite direction but didnt notice the wheels.

What time did you go up Mt Wellington? I went for a cruise up there 2 LOL

Looking at the photo info, the last pic was taken at Mt Wellington @ 1:52PM, too bad it'd wouldve been good to meet you :)

I saw you both on my way back down to Hobart :)

I hope you didnt see me on the Midland Hwy.

I was... erm, a bit over the speed limit somewhat, very keen to get home and relax by then :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Half anticipating the next question then: I have two magnets stuck in my oil pan. What should I do? 
    • If it's magnetic what is stopping you from using a magnet on a thin wire from fishing it out?
    • Those 2 solenoids in that assembly I mention, are the PWM solenoids for torque converter lock-up clutch & EPC (line pressure control) ~ when most folks hear of 'solenoid failure', the tendency is to think electrical failure...but fact of the matter is, especially wrt the EPC solenoid (which is moving/running all the time), you can have an electrically 'good' solenoid, that's absolutely broken/worn out mechanically inside...ie; valve plunger return spring rubbing against spring retainer plate, lowering preload pressure.. ...and the solenoid armature extension limit spring wafer with bad wear/broken off petals... ...and if there's ever been any metal flying about, damage to the valve plunger end itself... ...the stuff one never really sees, unless you go the whole 10yards trying to answer the question "why is my line pressure screwy, but TCU isn't flagging any EPC solenoid fault?"...and carefully dissect the solenoid. Worst (and most probable) scenario is when the plate spring petals break off, they get held by the magnetic flux, get mashed up by the armature into little bits, which end up in the space between the armature & shading core bore, and things get stuck or randomly jam up, and your line pressure goes flat and doesn't change...and the TCU never sees it, as it doesn't actively monitor LP... ..then it gets into insidious land, if you end up with lower than expected line pressure...lets say high clutch..and the lower pressure causes it to slip ~ when I say 'slip', think say 2000rpm on the drive plates, and 1800rpm on the driven plates, because the slip is making them under-rotate by 200rpm ; you get all the usual nasties like heat and band/clutch wear, but even if it's only 20rpm slip the same thing happens...and... you'll hardly ever pick this up driving the thing with the torque converter active as it effectively masks these sorts of slippages that are line pressure related ...(the newer TCUs can detect clutch slip rate)...just  FYI as it were...  
    • There's nothing that some paddle pop sticks and extra cable ties can't fix.
    • Hey guys, so Golebys has good prices on Bosch injectors, and also sell an adaptor to go from 1/2 length injector to standard with the Nissan 10.5mm top seal.  Does anyone know if that adaptor is to suit the 14mm or 11mm injector tops?  And re. The bottom seal, to suit my standard RB20 intake, would I be right in saying I can just slip the 14mm square section O ring over the bottom of the new injector and done? Thanks in advance guy, Cheers, Rowdy
×
×
  • Create New...