Jump to content
SAU Community

Need S1 R33 Gunmetal Front Bar With Reo

corporateroller

By corporateroller,
in South Australia

 Share

Recommended Posts

corporateroller Apprentice

corporateroller

Posted
Posted

hey all, very desperate to borrow for 1 day for an inspection a s1 r33 gunmetal front bar.. there must be another gunmetal s1 r33 in sa somewhere so if u have a mate who has one, let him know and give him my number to call!!! 0431068346 (give us a msg about the bar and i will get back to you asap!!!). my reo bar has been cut for the intercooler/good look and the car is in extremely good condition... really desperate peoples as i wanna get this ride to sa plates.. thank you all in advance for reading this thread :(

D_Stirls Veteran

D_Stirls

Posted
Posted (edited)

So the inspection you are going through is the ID inspection?

If that's the case i wouldn't worry about swapping the reo over because all they are going to check is whether the engine number and chassis numbers match whats on the paper work.

The address for the ID inspection isn't even on the same street as the place you go when you are defected. If you are really worried take it to Sturt police station and get them to do the ID inspection (although they are only open 1 day a week for inspections).

Edited by D_stirls
Krishy Grand Master

Krishy

Posted
Posted
word of warning bro, ma mates friend apparently took a straight and clean s14 or s15 over the id inspection, stock as a rock apart from exhaust, turbo timer and boost controller, and they defected her for that!!

She prob didnt show any clevage then :D..........i knw of so many friends of mine that got away with so much shit by doing that.......one of my friends got caught sliding and bit of clevage and crying saw her getting off with nothing but a $150 fine for noise pollution (scretching tyres).....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Shoota's R33 GT-R RB30/26

      By MBS206 · Posted

      Ha ha ha! I know those feels mate I've finally got the garage cleared enough that next weekend I'll do some actual work on my car (hopefully). Unfortunately garage isn't usable after 10am at the moment That said, I've done a lot of work this weekend on helping finalise a friend's Production Race car. Full started Christmas Eve. We're down to about 8 tasks on the list, including "get a wheel alignment". Sometimes it's just easier working on someone else's car or project than our own stuff 😛
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      Ha ha, ended up going it alone.  I just sent it (in a very nervous fashion).  Once I'd released the locks and it didn't automatically start spinning out of control i felt a bit more confident.   It made some loud sounds (cracking and creaking noises) when I first spun it which got the heart rate going again!  I couldn't bring myself to leave it tipped on the side.  I feel a bit more comfortable having back right side up while it sits there. I'd get angry with your last point but you're 100% correct! 😅 Even yesterday I managed to distract myself at numerous times to make a bracket to fit an LED flood light off the back of the house and fix my sons pushbike.  There were other little taks nibbling at my brain for the rest of the day too...
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      Probably one of the more nerve wracking experiences of my entire life! 😂😂 The balance (centre of gravity) is out still but in a direction that gives me comfort!   It's quite bottom heavy still meaning it takes a bit of muscle to rotate it.  The plus side of that is that it wants to to go back to upright.  Better that than wanting to go all stranded turtle on me!
    • Duncan
      R32 GTST - 600KW+ RB28/CD009 Build

      By Duncan · Posted

      hmmm that's not ideal. This is a pretty new engine right, will be interesting if your engine guy has any theories about causes
    • TurboTapin
      Hicas ball joint install tool

      By TurboTapin · Posted

      A universal ball joint removal c press kit is better money spent and will work for the Hicas ball joints.  Here's a 45$ CAD Example. ATPEAM Heavy Duty Ball Joint Press Kit with 4WD Adapters | Professional 4 in 1 Ball Joint Press Removal and Installation Tool for Cars and Trucks | Universal Ball Joint Tool with Storage Case, Ball Joint & Tie Rod Tools - Amazon Canada
×
×
  • Create New...