Jump to content
SAU Community

Recommended Posts

this it not funny. how about in future if you see a thread posted in the wrong section instead of whoring it up as usual, hit report post and a moderator can move it to the relevant section? that would be much more constructive.

and for mark, if your GTST is completely standard I would say you can get away with 95 if you wish, but once you have a few mods like more boost, exhaust, tune etc then use of 98 is pretty much mandatory. and to be honest even in a standard skyline I would personally only use 98.

Link to comment
https://www.sau.com.au/forums/topic/220509-98ron/#findComment-3888627
Share on other sites

this it not funny. how about in future if you see a thread posted in the wrong section instead of whoring it up as usual, hit report post and a moderator can move it to the relevant section? that would be much more constructive.

I already had this morning.

Link to comment
https://www.sau.com.au/forums/topic/220509-98ron/#findComment-3888666
Share on other sites

this it not funny. how about in future if you see a thread posted in the wrong section instead of whoring it up as usual, hit report post and a moderator can move it to the relevant section? that would be much more constructive.

and for mark, if your GTST is completely standard I would say you can get away with 95 if you wish, but once you have a few mods like more boost, exhaust, tune etc then use of 98 is pretty much mandatory. and to be honest even in a standard skyline I would personally only use 98.

Here here.

Link to comment
https://www.sau.com.au/forums/topic/220509-98ron/#findComment-3888676
Share on other sites

98 is recommanded (& must for modded cars), but I think you can get away with 95 for fairly stock car.

Well I only use 98 (BP ulitmate & Vortex 98), a friend from work uses regular 95 on his 180sx & it seems to run fine.

Then again, his car does seem to sh*t itself everynow & then... not sure if its the fuel though.

Link to comment
https://www.sau.com.au/forums/topic/220509-98ron/#findComment-3888815
Share on other sites

and for mark, if your GTST is completely standard I would say you can get away with 95 if you wish, but once you have a few mods like more boost, exhaust, tune etc then use of 98 is pretty much mandatory. and to be honest even in a standard skyline I would personally only use 98.

My car is standard, and pings a bit on 98RON. I would never ever ever put 95 RON in it.

They are designed for 100RON!! Why be so nasty to your car. If you can't afford to put the proper fuel in your car go buy a Charade. They go hard.

Link to comment
https://www.sau.com.au/forums/topic/220509-98ron/#findComment-3890376
Share on other sites

I checked timing last night and it was a fraction advanced, now it's dead on 15 degrees. It's better, but still get a very small amount of knock at 3000RPM on 7psi (boost solenoid trick).

Spark plugs are tan coloured, so it could handle being a touch richer but they look fine for a standard engine. My exhaust is all standard, I would probably get some gains by getting a dump/front pipe and higher flowing cat. Since the skylines run richer once you open them up it might be just enough to make a difference..

Link to comment
https://www.sau.com.au/forums/topic/220509-98ron/#findComment-3891425
Share on other sites

My car is standard, and pings a bit on 98RON. I would never ever ever put 95 RON in it.

They are designed for 100RON!! Why be so nasty to your car. If you can't afford to put the proper fuel in your car go buy a Charade. They go hard.

sorry but that is codswallop. :( they are not 'designed' for 100RON. I would love to know where these myths come from.

Link to comment
https://www.sau.com.au/forums/topic/220509-98ron/#findComment-3892997
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hey all, I'm working on a project car and I believe I made some mistakes. I'm looking to remove the clear coat from my car on most panels (except for panels where the paint has blistered, I will sand this), but wanted to know if these steps are correct?   1) Get a red scuff pad (abrasive one) instead of sand paper to remove the shine from the surface 2) get 400 grit sand paper and go over the entire car with a random orbital sander so the surface is smooth and the primer can grab onto something 3) On the blistered paint, go over it with around 120 grit sand paper, go to 240 to smooth out the scratches, then finish on 400 grit. Anything to add in here or any feedback?
    • Agreed, another vote for the Haltech CAN wideband.  No voltage offset errors is a beautiful thing.
    • Just get a Haltech CAN wideband, no need to wire any delay circuits, or relay, etc. Since I've moved to a Haltech CANbus wideband, I have not replaced a single sensor for over 5 years (if not longer, can't remember when moved to Haltach).
    • Small analogue delay circuit with a relay. Just need a trigger, say, fuel pump running for more than 5s or so? Or, you could go full mental and write a sketch for an Arduino.
×
×
  • Create New...