Jump to content
SAU Community

Recommended Posts

So i've received a fine for under 15km/h which is 75 and 3 points. i think this was in a 50 Zone near anzac parade.

i've only just bought the car within the last 2 months. and it was on the written off regester, the previous buyer bought from auction and repaired it..

and its a diesel, so its surely no performance car at all.

now i've tested the car with a gps since the fine and my speedo is out. by a few km/h up high and a little more down low

would i have a leg to stand on in court representing myself? or would someone suggest a lawyer?

or should i just cop the fine even tho i thought i was doing the correct speed at the time.

the money from the fine isnt an issue, nor the points... i just want to keep my licence perfect :D

Edited by Angus Smart
Link to comment
https://www.sau.com.au/forums/topic/220535-contesting-a-speeding-fine/
Share on other sites

to tell the truth, i dont think its there problem if your speedo is out or not... I rekon you will get done even worse if you take it to court... I know it sucks and all but if it was me, id pay the fine, cop the points and fix the speedo... good luck to you if you take it on tho.

Anzac Pde is a 60 zone (mostly) untill you get to Alison road then it becomes a 70 zone all the way untill the end of Sydney Boys high. Obviously during school times the 70 becomes 40 zone.

The section you are talking about which has the camera is on Cleavland Street and not Anzac Pde, along the Sydney Girls side is where the camera is.

It's been there for months and months. Initially (as with all new cameras) there was a "warning issued" to speeders. But I guess that's expired.

The Cleavland street section is a 50 zone. Heck the whole of Cleavland street is 50km/hr.

Maybe you could try and say it's your first fine etc etc and get off it? Dunno

there is already a 10% speed allownace in place with nsw police i belive?

this allows people with speedo that are out with old cars get a way with an amount.

eg:

40kmph your allowed 44kmph

50 allowed 55

60 allowed 66

and so on .........

i dont think cops in nsw book you under the 10% differance, but Vic they do.

What was speed the cop put on the ticket?

What was speed the cop put on the ticket?

He got done by a fixed speed camera..

There are 3 signs before the camera and plenty of 50 zone signs at the sides, even on the ground it marks "50"

I love doing the speed limit there and seeing annoyed drivers tailgating me, coz they think that im going too slow, then over take me and speed up as they pass the camera. *FLASH* haw haw. :bunny:

Happened one night last week... Idiot car behind me was tail gating me.. I trott along slowly... She over takes me (Honda CRV Sport), just as it happen *FLASH* think I was in the flash too but I know I was doing 40km/hr so hopefully I wont get a fine. Otherwise id be pissed, and I have details of the other car anyways.

YOu can contest it, use the law mentioned above which allows a 10% tollerance eithaer way on your speedo, it takes awhile but it will have you with a clean slate.

for starters I'm not convinced that the allowance for speedo inaccuracy is law set at 10% and even it if is my maths tells me that 15km over 50km/h is 30% over 10kms would be 20% over. so unless he was only 5kms over that is not going to hold weight.

He didnt mention his speed, at least I didnt read it .. 15 and under is the lowest speeding fine you can get. I was just giving advice based on this law.. and yes its about 10% but Im not 100% sure.

This 15 and under is crap I think as it holds the same fine as someone doing 15 over the speed limit when he perhaps did 55kmph (which im pretty sure he could not have done as im pretty sure the fact is the the speed cameras flash at 57km/h 12% over road speed) I feel there should be a lower fine of 5k over and 1 demerit point.

In regards to the speedo it need to be calibrated on a dyno, from factory speedos come either to fast or more often than not to slow thats why the 10% leway exists. Oh and this is up to you to fix

Edited by DECIM8

I got done in a work truck, the speedo was out, i thought i was doin 95 but in actual fact i was doin 105. it was a 90 zone, work got the speedo check and found it was out , my boss rang the police or someone told them they changed the fine and loss of pionts but i still got done for 5 over.

  • 2 weeks later...

You're speedo, you're responsibility unfortunately. And with speeds, generally if it's done by us and not the camara we will put you give you the lower out of the 2, i.e. 15 and under rather than over, with all honesty you don't stand a chance in court. What people don't seem to understand is that a Magistrate can impose a higher fine than the IPB regulates if he feels it is a waste of the court's time, plus you will be issued court costs of $76 for the day, and Legal Representation if you had it.

Better to just pay up and be more cautious next time but its up to you at the end of the day =)

YOu can contest it, use the law mentioned above which allows a 10% tollerance eithaer way on your speedo, it takes awhile but it will have you with a clean slate.

There is a 10% speedo tolerance in the ADR's for vehicles manufactured after some date like 1976 but your information is incorrect. The speedometer can only 10% MORE than the actual speed of the vehicle. So if you are doing 60km, the speedo can read 66km, not vice versa.

Cleveland St has been a 50 zone for years and years. The cameras have been there since last November and there were big flashing messages boards there for 4 months.

No point going to court an saying you "Thought you were doing the right speed". You have to prove to a magistrate that either you WERE doing the speed limit or the camera was inaccurate. Good luck trying to prove either of them I'm afraid.

Idiot car behind me was tail gating me.. I trott along slowly... She over takes me (Honda CRV Sport)

Its not her fault VTAK kicked in while she was behind you. :yes:

And its a CRV Sport. If it wasn't meant to go fast, they wouldn't have called it a Sport.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As GTS mentioned, it takes a bit of faffing, some fiddling and a little modifying.  With the strainers, you can buy different styles. Some sit flat on the pump, some angle down.  Here are some photos of mine, ignore the ugly welds lol. 
    • The smart thing is to actually locate the pump at the right point down the hanger, so that the strainer can stay sticking out at a right angle, but near the bottom. This is the perpetual hassle with retrofitting any different pump to the factory hanger. Some just go where you need it to, some need fiddling and faffing, and modifying of stuff.
    • Some updates. After a lot of praying and some inspecting of crank threads, we've found that they were both kinda munted but nothing seemed terminal. The other option was drilling and helicoiling the crank. That is obviously the last option so we decided to at least try to get a OEM GM bolt in to GM Specs. So after honing/linishing the balancer from it's .002" interference fit to a .0018" to .0015" to .0013" it eventually slotted on to the crank. ATI state the interference is nominally 0.0007-0.0009... so it's still snugger than ATI reckon and explains the issues we had to fit the thing to begin with. New GM bolt went in at 37 ft/lb then torqued 140 degrees after which was EXTREMELY   but it tightened up to 140 degrees and it was a lot of force. So all things considered, the balancer is secured to the exact specs that GM want with the OEM Stretch bolt, (that ATI say you can use..) and the balancer itself is seated and snug AF. So WOO. Engine is now back in the car with lots of swearing. Bellhousing bolts done up, driver side manifold is on, AC Compressor and hard lines are back on the car. Next step will be to connect various engine bits/wiring/intake/radiator etc. Then oil and coolant and ... test start it? And of course, looking into this issue... which actually doesn't look so bad - It looks like it can be twisted back into shape with a set of multigrips. Anyone wanna buy my bonnet? Boy it looks good over there and sunk cost sucks.
    • Also this may be a stupid question, but how would you recommend getting the strainer on a downwards angle ? as they tend to obviously clip to the bottom of the pump which usually sits level 🥴
×
×
  • Create New...