Jump to content
SAU Community

Recommended Posts

Hey everyone, ive just bought myself a r33 series 2 and i have a question, on the dash (right beside the speedo) there are a set of 7 lights, the one furthest to the left on the bottom row shines green whenever i start the car up, any ideas what ths light is for, i was thinking possibly a warning to do the timing belt as the car has just turned over 100000kms, the timing belt has been done however??? any help would be good, cheers

Link to comment
https://www.sau.com.au/forums/topic/220727-what-is-that-light/
Share on other sites

Check out this thread, they have a green dash light too..

http://www.skylinesaustralia.com/forums/Sp...ng-t206742.html

Weird. I have a green LED in the same spot as the ones in that picture that does the same thing; comes on when the Fog lights do. It just serves as a reminder that the foggies are on, just in case your Skyline doesn't beep-nag you to death if you forget.

Rip out the cluster and follow the wires, see where they go.

  • 1 year later...

^^ Looks like its a compliance thing as theres no way thats factory! Looks like shit!

lol on it being a timing belt light...that would be funny.

Toyota Hiace's have a timing belt light, it flicks on every 100,000km, and to reset it, you take the cluster out and move a small screw from one hole to another, re-setting the timer for another 100,000km... moving the screw back again when it clicks ANOTHER 100K :sick: and so on.......

Edited by gotRICE?

Wow, Australian has some ass requirements for jap cars!

Pretty sure the thing beeps at you same as the headlights doesnt it? Because it switches the park lights on too.

Well, does in mine anyway and i dont have fog lights! The switch just turns on the parkers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just install a grease nipple into the centre of the outer steel of the FUCA. Make sure the bushes aren't long enough to touch each other underneath that nipple. Cut a few mm off each if need be. Then you can push grease in there while it is all assembled. That was the very first thing I did (to all 4 ends) of the FUCAs on my 32 when I put Whiteline adjustable bushes into them. They would squeeze the grease out real fast, and I could squeeze it back in faster.
    • @GTSBoy I found the issue (sort of) when I took apart the bushing again, it was completely dry inside! When I experimented with it, all the grease would push out when I would compress the bushings. I wonder if this has anything to do with me putting in the poly bush first on both sides and then pushing in the metal barrel. Maybe I should have put in the metal barrel first then the rubber bushings so the spread pattern is different.   It's fixed (for now).
    • Just redid that entire job. 4 hours, but tightened everything properly. Had to jack the rotor instead of having the car on blocks as there was no room for the FUCA arms to tighten and the j arm. All good now. Cheers for the help!
    • I would sell those side feeds before you hydra-lock a motor. I won't say too much about Yellow Jackets because I'll hurt people's feelings, however ask those that tune RBs day in/out what they think of them.
    • The 1000ccs are side feeds but they're not currently installed, had my old factory ones in for leak testing purposes, only decided on them because front facing plenums and good top feed rail kits are out of my budget at the moment, are they really that problematic? Had a set of yellow jackets that lasted me 5 years, no real issues, only replaced them chasing this misfire issue that ended up not being ignition related 😄  
×
×
  • Create New...