Jump to content
SAU Community

Recommended Posts

like im sure many of us i drive my gtr to work for a bit of fun but with petrol its getting outs control lol

anyone thought of putting lpg on thier gtr?

i think gas research would be the only way to go due to the injection not beeing able to keep up with the power of gtrs.

previously i converted a 180sx with a ca18det (4 yrs ago ) and it produced 220kw atw, on gas research,

any thoughts?

Link to comment
https://www.sau.com.au/forums/topic/221155-gas-on-a-gtr/
Share on other sites

like im sure many of us i drive my gtr to work for a bit of fun but with petrol its getting outs control lol

anyone thought of putting lpg on thier gtr?

i think gas research would be the only way to go due to the injection not beeing able to keep up with the power of gtrs.

previously i converted a 180sx with a ca18det (4 yrs ago ) and it produced 220kw atw, on gas research,

any thoughts?

Fark gas research the shit is archaic... lpg injection is the only way to go. I am tuning a 280-odd rwkw gas research soarer ATM and well yeah... injection FTW Gas Research FTL.

Link to comment
https://www.sau.com.au/forums/topic/221155-gas-on-a-gtr/#findComment-3899387
Share on other sites

sorta off topic but once all these conversions are done and everyone's paid at least 1g for it.. what do you think the government will do for tax and shit on the gas? the price will shoot up too.. i think it depends on the car and how much you fill up.. get ur monies worth..

thats if you can do it that is

Link to comment
https://www.sau.com.au/forums/topic/221155-gas-on-a-gtr/#findComment-3900363
Share on other sites

HEY GUYS, My R34 is injected, iv maxed out my 6 injectors at 250rwhp so to get to the majical 300rwkw mark i would have to go to 12 injectors and 2 gas convertors. the gas injectors can flow alot more IF you run them on custom fuel rails. as the standard Keihin 1's are a major bottle neck.

regards

chris

Link to comment
https://www.sau.com.au/forums/topic/221155-gas-on-a-gtr/#findComment-3900915
Share on other sites

With gas research there is some nice example's out there like a mustang with a 4ltr engine making 470kW atw. But it cost lots of money cheaper to stay with petrol.

dinosaurs for dinosaurs :blink: im notsure if many people who comment on the gear have actually used it.... gas can be real laggy to respond to throttle inputs and ALL the gas research units ive driven or seen suffer from this, the direct injected stuff is exactly like petrol... no throttle lag.

Link to comment
https://www.sau.com.au/forums/topic/221155-gas-on-a-gtr/#findComment-3902599
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 😑. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
    • Hey everyone, This is my first post apart of the introduction. I tried searching a bit on the forum but couldn't really get a straight answer. I got the car to my mechanic as I felt it being weak. It seems that it was missing on two cylinders due to the injectors. I had all my injectors clean and the car runs much better. The mechanic also confirmed my suspicions that the cat is clogged and needs to be tackled asap. The cat rattles a bit and the hot exhaust warning frequently lights up when driving after getting the injectors clean. In my introduction I was asked about what modification I might be interested in and mentioned a cat delete. From what I was told, this is not really beneficial on the RB20DE and there are more cons than pros.  Could perhaps anyone give some suggestions on what the best course of action would be since the current cat is toast and needs to be removed/replaced anyway? I can also sometimes smell a strong smell of fuel, but I'm not sure if this is related.
    • Hope the cans went down well at least 
    • 255 can't go wrong with the price.
    • When I was replacing my pump due to being stranded in the wrong state, I went with the Deatschwerks 320lph kit. It is a direct plug in to the stock wires, harness, everything. It comes with a plug... but you can plug the OEM plug directly into this thing. https://justjap.com/products/deatschwerks-dw300-fuel-pump-nissan-s13-silvia-r32-r33-r34-skyline-c34-stagea?currency=AUD Downside: Won't actually flow that much on boost if you want to push it on E85, but it's comparable to the 040/255 etc. Little more actually.
×
×
  • Create New...