Jump to content
SAU Community

Newbie Question About Pod Filter And Bov

POLICE
 Share

Recommended Posts

POLICE Mentor

POLICE

Posted
Posted

Hey guys

I've put a new pod filter in my skyline due to the piping of the FMIC

anyway it's making shitloads of boost sound even at 2000rpm

is there a way I can control that like buy a boost controller or something???

I really have no idea about forced induction stuff

so if any1 has a pic of where they installed their boost controller that'll be much appreciated

Thanks

POLICE Mentor

POLICE

Posted
  • Author
Posted (edited)

I've actually got the airbox, the brand is the netami gold pod filter

there is a hole where the old SMIC piping was,

of which I connected a tube for air intake under the front bar

it makes less noise with the air box but still quite annoyiny when all I want is to drive it normally

the standard airbox can be modified but I'd have to cut a large chunk out of the air intake

which will render it to be not very efficient

Edited by POLICE
(OO)SKYLINE(OO) Grand Master

(OO)SKYLINE(OO)

Posted
Posted

When you gota pod filter on, it will make that sucking noise. Its what a pod does.

No point putting a boost controller in to lower the boost on your stock turbo. (BTW Your turbo is stock right?)

I like have the sucking noise with my car, sounds great!

JAS-25T Grand Master

JAS-25T

Posted
Posted
I've actually got the airbox, the brand is the netami gold pod filter

there is a hole where the old SMIC piping was,

of which I connected a tube for air intake under the front bar

it makes less noise with the air box but still quite annoyiny when all I want is to drive it normally

the standard airbox can be modified but I'd have to cut a large chunk out of the air intake

which will render it to be not very efficient

What material is it made from? paper? cotton? steel?

If you want to keep the pod - get one that is paper or cotton - that will quiten it down.

else

fit the stock air box up with a paper or highflow panel filter.

4drftn Experienced

4drftn

Posted
Posted

i know what you could be going through, i just took the pod filter of my v8 ute and put the the big airbox with over the radiator surround intake (mouth) because the sound of the induction noise on the pod (paper filter) was very loud, even idleing...

but the HKS pod pn (foam pod filter) my r33, the induction noise gets louder when you are comming onto boost, i do like the induction noise it gives, a deep howling noise...

R338OY Veteran

R338OY

Posted
Posted

The induction sound is air sucked through the pod AND the compressor turbine spinning and compressing that air, which was previously muffled with the stock airbox + filter. It's normal (and sounds sahweet) as you come on boost from around 2000RPM+.

RBwhatever Veteran

RBwhatever

Posted
Posted

haha @ GTST.

There is no way of getting rid of the induction noise with the pod, even if you box it. You'd need some thick heat insulation in there to make quieten it down, but even then I'd highly doubt it'd get rid of the noise like a stock air box.

Pod induction noise, you either love it or hate it. Or just learn to live with it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a · Posted

      So been ocd with timing mark but checked from few angle and seems both cam are on and crank is matching as well to the slot on sump and crank pully   i noticed crankshaft cover has been robbed as per attached pic. Any ideas why? Could my balancer or harmonic be on its way out? should I replace the cover? https://ibb.co/ZR1JFYRR
    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a · Posted

      So now doing the change and first time dealing with rb so little nervous giving engine power and potential for screwing it up When you align all marks and then remove crank bolt, timing move little I assume you can put the bolt back in once you have removed the pully to get timing to where you want?   here is pic of my both intake and exchust cam aligned, depending on angle you look they seem to be either aligned or a half tooth or so out. Any thoughts? Should you angle your face and look at each mark that way as if looking straight rather than from above as it can be misleading   <a href="https://ibb.co/ZpnhcvbF"><img src="https://i.ibb.co/HfWrGR9b/IMG-4447.jpg" alt="IMG-4447" border="0"></a> <a href="https://ibb.co/4wm2wn4q"><img src="https://i.ibb.co/JWBqWwr1/IMG-4445.jpg" alt="IMG-4445" border="0"></a>   https://ibb.co/ZpnhcvbF https://ibb.co/4wm2wn4q
    • sunsetR33
      braided lines for the turbos

      By sunsetR33 · Posted

      Thanks for the reply @GTSBoy Haven't really thought of that yet, but you are right. If the hose was damaged it should be absolutely pissing by now. I'll put some heat sleeve around it for good measure since I'm already removing the line anyway.  Maybe I'll put on some of the stock hardlines if I ever fully remove the turbos again. Maybe when T51R modding the compressor housings? Might be a fun mod on GT28s for that "fake single turbo" effect.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 1: I did some work on the car already before finalizing this post and my "issues" list. I dropped the Tomei exhaust in favor of the HKS Hi Power Silent. Sounds nice and I can actually hear myself think now. Also gives me a realistic chance to legally drive without silencer inserts. A bit of cheating was necessary to still be able to mount the Top Secret style diffuser. Some malusage of washers and a bit of "convincing" toward the brackets and exhaust hanger seemed to do the trick. The shaky steering wheel has been resolved as various suspension components were worn, like sway bar bushings and link bars. Most notably the two steering tie rod ends. Had some trouble finding bushings because my sway bars are not OEM thickness, 23.x up front and 27 rear. But non adjustable, so no aftermarket I suppose. Maybe they are nismo units? Turbo oil drain hoses were definitely still the originals and are new now. Wasn't the cause of the turbo oil leak sadly. Currently removing the rear turbo because of it, I suspect the braided oil feed line is the culprit. This issue needs to be dealt with so I can work towards actually getting the turbo setup legal and inspected. Two new issues to add to the list as well. Rear Main seal is probably leaking. Time will show how bad it is, I don't really want to drop the gearbox right now just for the stupid seal. Could fix a few other things in one go once I do that. Front right driveshaft grease is going past the cv boot, so at some point I'll fix that too.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Ok so no 4cyl clutch... Yeah it is a factory manual. So if iam correct i need clutch and flywheel too? I can use something that suits something like R32 GTST?   EDIT: https://www.ebay.com/itm/224291042776 Is this ok?   EDIT2: i maybe forget to mention this(dk how important it is) but the trans will be behind RB25DET NEO(iam doing swap) It will be there for a little while. Iam planing to do bigbox or BMW tranny..
×
×
  • Create New...