Jump to content
SAU Community

Recommended Posts

Have a Things to Do list for the GTR 32.

Can any of you help me price the following??:

-Replacing Timing belt and tensioners

-Bleed brakes and change all 4 pads + machining

-Bleed Power steering and replace

-New clutch + thrust bearings etc, and whatever else while the gearbox is out

-Cam Gears

-Flush and replace coolant and thermostat

Thats all for now i think.

Thanks,

-Phil.

Link to comment
https://www.sau.com.au/forums/topic/222281-price-check-please/
Share on other sites

-Replacing Timing belt and tensioners

-Bleed brakes and change all 4 pads + machining

-Bleed Power steering and replace

-New clutch + thrust bearings etc, and whatever else while the gearbox is out

-Cam Gears

-Flush and replace coolant and thermostat

Here's some really wild guesses.....

- When you do the timing belt, do the alternator/aircon etc belts at the same time if they're not 100%, id guess 1200-1500 for all this if using nissan parts. You might need cam seals at the same time....

- Unless you need to machine the brakes, dont bother. Just sand it dull with wet and dry. Do it yourself. Price will depend on pads which could be anything from $75-400 a pair depending on what you get.

- Power steering bleeding is just done my turning the steering wheel all the way to the left, then to the right and repeat a few times. To replace the fluid, shouldnt be much, <$100

- Clutch, depends on what you get, maybe around $1000-1200 all up.

- Cam gears will need a dyno tune to get right, maybe $900

- coolant and thermostat maybe $50

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey @Butters, did you end up getting this clutch in ? I have just ordered to a uniclutch track to go in my getrag 6 speed that’s in my BNR 32     
    • I know you don't want to hear this comment, but I can't not say it.  I just can't see 200kw being worth the time and effort. Its like guys with NA cars, putting in headers/exhaust/tune for a massive 20% jump in power. Great, the slow car is still slow and you're down $10,000.  My vote is leave it NA or price in a gearbox upgrade and shoot for at least 300KW, preferably 350KW+.  Now you have a NC that will try to kill you from time to time and will be exciting to drive
    • Ah yep. The main message I want to pass on is, try not to get scared of ghosts when thinking about knock/knock detection.  What I mean is, healthy engines make noise. Knock is also noise. Your knock sensor and ECU combo are trying to determine bad noise from good noise based on how loud the noise is. The factory knock sensors and ECU are not good at doing this.  Modern ECU's are pretty decent at it, however I'd still say that you would want to verify that if your ECU says it's knock, that you actually listen to it and confirm that it is correct.  Are you familiar with the plex knock monitor?  https://www.plex-tuning.com/products/plex-knock-monitor-v3/ I expect you're the type of person that would be very keen to play with something like this. It is great knock detection and you can pop some headphones on and listen to what's going on.  Knock that you've deliberately induced in low load low RPM areas is not really putting anything at risk and is a great tuning/learning/verification tool.  I just thought this was worth mentioning based on the way you were talking about setting up a base map and the Haltech base map settings. There are better ways to spend your time then chasing ghosts and worrying about detonation in scenarios that it is crazy unlikely to encounter it.  I was also wondering, what ECU are you planning to get? Will it be long til you pick it up?
    • This came quicker than I thought. It ain't even 2025 yet.
    • I somehow quoted my post instead of editing it. I regret nothing.
×
×
  • Create New...