Jump to content
SAU Community

Recommended Posts

i'm off to get my 2835 installed in a couple of weeks so i decided to do a few of the less time consuming supporting mods myself... (fuel pump etc)

so i installed some new splitfire coils and some bcpr7es gapped to 0.8... and put the car back together

when i took it for a drive i noticed 2 things...

1) it feels smoother and more linear throughout the rev range

2) its running less boost. ?!

formerly i was getting .9 bar with boost controller (bleeder) switched off but spiking out to 1.1

now its getting .5 bar and not spiking past .55

so i turned up the bleed valve to .8 bar and it holds nicely without spiking past .85ish

car has pfc, fmic, turbo back etc. how much boost shold it be producing with these mods?

also when the car was tuned a year ago @ racingline, nige said there was a tiny leek that he didn't have time to locate,(i needed transport back) but the car was running fine and not to worry. the car ran strong for a year with no problems.

so... my question is this...

was the car running with a leek that was acting like a bleed valve and upping the boost for a year

OR

did i not put a hose on properly this time? (i have checked and checked again...)

Link to comment
https://www.sau.com.au/forums/topic/222437-interesting-problem/
Share on other sites

Oh and they're gapped to .8 cause i've been told by many many people that would be the optimum gap...

On a stock ecu/tuned car running 98ron yes

With an aftermarket ecu, tuned and new splitfires your gap should be 1.1..

The idea of setting the gap to .8 is a cheap get around for the pinging/breakdown issues most skylines have on 98ron when using the factory tune.

It's a stop gap, for peeps that can't do it the right way atm...with your parts you shouldn't be bothering with that crap.

Embrace the strength of a bigger spark!!

I did the same thing when I first got my nissan, until I got around to doing it right.

i dunno... taking all that shit off again... might give it a go when i get round to installing those injectors that are still sitting in the box next to my bed :thumbsup:

any ideas on the prob guys?

Even once the coilpacks are "coated in silicon" the car will fart and miss above 5000RPM if you gap is at 1.1mm WHERE IT IS MEANT TO BE!

Once you chuck the Splitfires in, (Or even BRAND NEW stock coilpacks) you will be able to gap plugs to 1.1mm AND rev to redline perfectly cleanly, producing a better flame front in your engine.

Technically, from what I can gather, it will also allow you to run slightly more advanced timing when you do the tune, as you have a wider initial flame front.

Hence @ 1.1mm you should be able to make more power cleanly...

Even once the coilpacks are "coated in silicon" the car will fart and miss above 5000RPM if you gap is at 1.1mm WHERE IT IS MEANT TO BE!

Once you chuck the Splitfires in, (Or even BRAND NEW stock coilpacks) you will be able to gap plugs to 1.1mm AND rev to redline perfectly cleanly, producing a better flame front in your engine.

Technically, from what I can gather, it will also allow you to run slightly more advanced timing when you do the tune, as you have a wider initial flame front.

Hence @ 1.1mm you should be able to make more power cleanly...

Depends on a variety of things but, in this case the 0.8mm gap is going to be better at high rpm/boost and power levels in terms of reliable spark.

1.1mm is a nice gap for a cleaner burn at lower rpm, hence it's factory.

The factory coils are just as good as splitfires by the way. Splitfires are just cheaper to buy new.

Depends on a variety of things but, in this case the 0.8mm gap is going to be better at high rpm/boost and power levels in terms of reliable spark.

1.1mm is a nice gap for a cleaner burn at lower rpm, hence it's factory.

The factory coils are just as good as splitfires by the way. Splitfires are just cheaper to buy new.

How do you figure a smaller spark is better on higher boost?

Gapping down is a very basic and simplistic way of advancing timing...used to get around pinging on a stock non-tunable ecu.

If you tune the car correctly with 1.1 gap it is better...you can actually feel the difference in top end, revs more freely.

Splitfires don't create more horsepower, but they do give a stronger spark (%20?) which certainly helps.

But hey if 8 is your lucky number.... who am I to say different.

How do you figure a smaller spark is better on higher boost?

Gapping down is a very basic and simplistic way of advancing timing...used to get around pinging on a stock non-tunable ecu.

If you tune the car correctly with 1.1 gap it is better...you can actually feel the difference in top end, revs more freely.

Splitfires don't create more horsepower, but they do give a stronger spark (%20?) which certainly helps.

But hey if 8 is your lucky number.... who am I to say different.

I'm sorry but, 'feeling the difference' in top end?

Unless the tune was rooted before I can assure you that not only is there no power difference but, also this 'feeling' is peculiar only to cars that started out with a spark issue or were seriously 'under-gapped' for the density of the air/fuel mixture.

Smashing more power/rpm/boost into a motor and gapping down on the exsisting heat range is tuning 101( for all cars). If you get no joy in the top end after gapping down on the exsisting heat range you go to a colder plug etc.

For example, for most of the NA V8's I've tuned you can just about go off a rule of thumb that is gap down 4 thou for every 50hp added.

I've been doing this to alot of different cars over the years so 'luck' has nothing to do with it. :)

There are some serious horsepower GTST's & GTR's running around with factory coils as well. Splitfires do one thing well and thats make a cheap replacement for the expensive factory coils when they are shagged. :D

Edited by rev210

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Got my R34 gearbox around 4-5 weeks ago. Came into some extra $$ recently and after I cleaned the mess off the notes, I thought, might as well buy that R34 box I've been pondering.  In that time I've pulled the engine out, replaced rod and mains bearings, done a few other engine things that are much easier with the engina out eg PRP oil pump upgrade, replacing wastegate coolant lines, installing Turbosmartass turbo oil pressure reg, made some mounting brackets for some of my mods that are "hard to reach", converted the R34 box to R33, put the engine and new gearbox back in the car. Plus cleaning ...Oh my god so much cleaning when doing such a project. Yep I'm a busy bee, buzz buzz. As part of the gearbox project, researched posts and found this thread (In which i nailed it for the OP), hence the post here # logical thinking.. Not all about you old boy, SOrrryyy. Dare I ask,  how's yours going ,> Or you got it done yet, and if so why didn't you post any of the tips I posted to help other members? ???      
    • Seems to be the case mate , still an OK price for a grey import.
    • I’m interested in the carbon diffuser fins and Toshiba MFD screen replacement if they’re still available.
    • @GTSBoy yeah i know it was not the "great" idea but it is and option...but i think i will stay on no BoV rather then trying to make it work with "half" this and that. But that GReddy FV2 is cool...i like that you can make it like stock if you want (and have/make the custom pipes) For other thanks! it was alot of information. But for the sound...a dont rly "like" both of them...specialy if they are loud...but if i "must" choose i would rather have little whooosh rather than sutututu with no BoV....BUT that is what is i gonna get. So for the all info i gather. In my case:  No BoV is not that bad cuz it is stock...and iam used to put N/clutch right after rpms are around 1000 so it should be ok...just need to avoid "big" drops. But i do not have the engine in the car so i do not really know how "bad" or good it is. But as i had that little test drive it looked ok. The atmo BoV should be worse car would dump to much fuel specialy between the shifts...so without proper tune/ECU i dont want that. BUT with that...car should drive ok with no problems right? (i do like there is less piping wih this solution) 🙂 
    • Usually an RB20 won't stay in closed loop idle anyway. The O2 sensor gets too cold, stops swinging.
×
×
  • Create New...