Jump to content
SAU Community

R32 Gtr Engine Parts Sale - Heaps Of Stuff!


Recommended Posts

ive got a heap of parts from 2 rb26 motors ive pulled apart, i am using the head and plenum setup but besides that its pretty much all for sale.

ill post pics below but here is the list of some of the stuff i have around, i have 2 of alot of things as well...

86mm bore block, some marks on the bores, needs a rebore to suit new pistons $550

32 gtr crank good cond was using standard size bearings and they were good cond when removed - $400

gtr rods good cond - $200

turbo oil and water lines

fuel rail

cam gears

inlet rubber pipes

twin turbo pipe

twin turbo pipe polished with new badge - $150

metal inlet pipes for turbos

no name bov - $80

power steering canister - $60

exhuast manifolds

exhuast manifold covers

direct clutch twin plate handles 600rwhp no problems, very little use - $700

lots of other bits and pieces, ask if i havent listed something u need from the engine as i havnt listed it all

I am in Perth but i can send parts anywhere, you pay postage though, and ill freight the block but the buyer can organise it as its not something i can carry into the post office lol

post-40430-1212910234_thumb.jpg post-40430-1212910257_thumb.jpg post-40430-1212910338_thumb.jpg post-40430-1212910350_thumb.jpg post-40430-1212910361_thumb.jpg post-40430-1212910372_thumb.jpgpost-40430-1212910388_thumb.jpg post-40430-1212910403_thumb.jpg post-40430-1212910418_thumb.jpgpost-40430-1212910418_thumb.jpg post-40430-1212910431_thumb.jpg post-40430-1212910446_thumb.jpg

post-40430-1212910461_thumb.jpg post-40430-1212910869_thumb.jpg post-40430-1212910910_thumb.jpgpost-40430-1212910929_thumb.jpg

post-40430-1212910827_thumb.jpg

post-40430-1212910841_thumb.jpg

post-40430-1212910856_thumb.jpg

Edited by unique1
Link to comment
Share on other sites

  • 4 months later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Weird the Gktech one doesn't have the 3 holes and is only a 5min install if you have the standard front bar.
    • Honestly, as someone on the standard PS4 controller, should be relatively easy to get gold. Remember you have more grip than you think.
    • Fitted some Advan AD09s to try next. Likely slower than the CR-S but should work in the wet and last longer.   Off for alignment and the new plates worked a treat! I was finally able to hit both my drift and grip alignment targets with the same setup! Grip Front: Toe total -2mm(1mm out each side) Caster +7° Camber -3.8° Ackerman +15° Rear: Total toe +3mm (1.5mm in each side) Camber -1.5° —————————————- Drift as above but drop the front sway bar and change the below. Front: Toe total -10mm(5mm out each side) Ackerman +5°  
    • @Duncan can you put the Link in, and measure all the power input voltages with a multimeter. Specifically looking for one that is low.   Then put the other ECU in that it runs on, and measure those voltages again with a multimeter?   If all of your voltages read normal on both ECUs, but the link is still reading low internally, your issue IS the LINK. If the voltages drop low on the multimeter while the Link is plugged in, but not other ECU, then the issue COULD be wiring in the car, or it COULD be the ECU. To rule out wiring, work out how with an ECU removed, you can trigger all the necessary relays, and then measure resistance from the pin that is reading low at the ECU, to the batteries positive power.   I have a sneaking suspicion your issue is the link, it's not reading the voltage properly, possibly a dry joint, or a Cap dieing, and because voltage is low, it's likely attempting to compensate on fuelling and the engine won't run.
    • Hi there, Does anyone here have the carbonetics slam panel installed on their R34 GTT? Or used to have one and got some pics of how it sat? https://carbonetics.net/products/1999-2002-nissan-skyline-r34-gtt-cooling-slam-panel?srsltid=AfmBOoo6Uz0nuxGI3qC0sn56KJI6PMgh0OvV-pbegsPDHTtTxz4IMljc I’m just trying to get an idea of how they sit once installed but these guys have no pics.  biggest question I’m trying to figure out is what the hell the 3 holes at the front of the panel are 😂 and where they bolt    Thanks in advance 
×
×
  • Create New...