Jump to content
SAU Community

Recommended Posts

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

At the moment, Sunday is mostly free at go karts, theres a bday group booked in at 2pm till 3pm I think but they said they could fit us in between races, ie, there 8-10 race then our 8 to 10.

As it's a bit late and we only have around 7-8 wont be booking in, everyone will need to pay individually. People tell me if they cant make it.

posted 2 to 3pm earlier as a good time, other bday group is booked in for that, which we could split the time with since they have only 8 as well, still an individual booking thing though. need to bring s helmet or use theirs.

Hey Cejay,

With all the ifs and buts, whats the final outcome?

I think from reading your posts - We pay as per normal 3x10min sessions (not booking an hour) but have an allocated time to drive? If I've got this right that sounds like the best way as people won't be paying for those not turning up.

posted 2 to 3pm earlier as a good time, other bday group is booked in for that, which we could split the time with since they have only 8 as well, still an individual booking thing though. need to bring s helmet or use theirs.
Hey Cejay,

With all the ifs and buts, whats the final outcome?

I think from reading your posts - We pay as per normal 3x10min sessions (not booking an hour) but have an allocated time to drive? If I've got this right that sounds like the best way as people won't be paying for those not turning up.

Yes you'd pay as normal for yourself only on the day.

The way the guy explained it is they'd like to know what time we'd show up, makes it easy on them. Essentially an unofficial booking. We can rock up whenever, but of course doing that won't guarantee us getting a run. It does seem to make the most sense, as you are just paying for yourself. The other way only really worked if we had 10 people which we don't.

Alright, booked in for 5 people so far, turn up at 1:45 to being race at 2pm, theres another group on during that time as well.

It's important you show up early to fill out the paperwork etc.

We'd alternate with them, 1 race on then them. So at this stage it will be 2 10 minute races for all up 32$. If we want more can decide on the day. At this stage after 3pm is clear. If more people want in please advise as I will have to call them to up the booking. Ie atm if family of 4 want in they would probably be chucked into our group at that time, at the same time we can't over book.

Just to confirm you guys will need to fill out the disclaimers and pay seperately, and will need an adr approved helment if you don't want to use theirs.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • FWIW the depth of the groove in the rubber pad is not super essential, the blocks are rubber and squish a bit. If you are worried an angle grinder will make a deeper groove quick smart
    • I mean, if you were to move the jacking points away from the original location, that is, away from the wheels and closer to the centreline of the car, then it will be more likely to overbalance and tip off the supports. Same as we talked about before. I was talking about moving for-aft. If the sill is bent outward or inward, then the car would obviously look unstraight from the outside. Hopefully that hasn't happened either. Again, you can do comparative measurements from the chassis rails to see if there is much deflection.
    • Can you elaborate what you mean with your first sentence? I meant move as in the bulge kinda seemed like it got pulled "outward" meaning it got pulled down and to the side with the jacking rail itself, so the load bearing bulge now sits lower than usual and is not level with the sill on the other side of the jack point. Either that or the jacking rail just got pushed in a good bit.
    • As well as being risky WRT tipping off anyway. Yeah, I wouldn't expect it to move. Just measure from the rear one to the front one on the good side, then measure that same length on the wrecked side. You will find the notches in the pinchweld, and the jacking pad. Just spray a spot of marker paint or something there.
    • but any other area than the bulge you are talking about will just cave in then? The front driver side is pretty bent so I don't know if that will work the way it is now. I can still kinda make out where that bulge is/was but it looks like the position of it also changed due to all the mistreatment? Hard to tell
×
×
  • Create New...