Jump to content
SAU Community

The Goods On Oils


PHaT MR30

Recommended Posts

He said he might be stocking Motul oils soon as well! Also mentioned he might be getting some Castrol synthetic 5w40 (i think it was) that is manufactured in Europe, meant to be pretty good by the sounds of it.

he already stocks the Germon Castol product. Thats the best.

Link to comment
Share on other sites

ADVAN reccommend Motul Le Mans 24hr 20w60

used it for a while, no issue's, smells nice

Have been using Penrite Sin 5w60 lately. Most of the racers at Eastern Creek have been using it aswell, since they change there oil at very small intervals and the price to performance ratio a major factor and it also has good resistance to fuel additives and methanol. I tend to go through my oil every 1000km-3000km with the power level, blow by and rich AFR's and methyl Benzene I run.

Have another track day on Sat, will see how the oil temps go. they are usually around 110c max. My car also runs quite rich so I opt for a thicker grade.

Value for money I like the Sin, Motul does seem to keep oil temps down a wee bit more, but the only good stuff is the 300V Chrono, Competion and Le Mans..and they cost a bundle.

Have also used Royal Purlple, which does everything its says...just not keen on running it continuosly as it has micro polishing beads...maybe every 5 services to keep my bearings smooth. I tend to use it after my run-in oil then switch.

At the end of the day, buy the best oil you can afford.

Edited by BOOSTD
Link to comment
Share on other sites

I just did an oil change on my rb30det which is 5000ks old. I used Castrol R synthetic 10w 60 the engine seemed quieter on start up it and it also has better oil pressure when hot Compared to the valvoline stuff i had in it.

Link to comment
Share on other sites

Had my oils changed yesterday.

Have no oils i can compare to but here are the oils i used and what it feels like.

Motul 300V Chrono 10w40 - Nice smooth idle. Nothing wrong with the car...maybe too early to make an assumption

Motul Gear 300 75w90 - AWESOME!!!! Changed my shifting to make it feel more direct and solid.

Motul PA90 - Diff whine has stopped especially when i first start driving the car

Link to comment
Share on other sites

hi all,

I have a R34GTT Manual, want to change the gearbox oil, does anyone know how much I need and any recomendations for what I should use? Thanks in advance.

Edited by LINEUP-NT
Link to comment
Share on other sites

hi all,

I have a R34GTT, want to change the gearbox oil, does anyone know how much I need and any recomendations for what I should use? Thanks in advance.

If you have an auto and want one of the best oils, Castrol Transmax Z is excellent. Ive used it on my car and its great. I like to drive spiritedly.

Link to comment
Share on other sites

If you have an auto and want one of the best oils, Castrol Transmax Z is excellent. Ive used it on my car and its great. I like to drive spiritedly.

have edited the other post, it is a manual. cheers anyway.

Link to comment
Share on other sites

I own a 1996 R33 with 84kms on the clock Rb25DET, I have read from the first post till the end of the page and im still confused what would be recommended for me. Could someone here honestly tell me the recommended oil. I am using it for daily driving, i will soon have a ehxhaust system all and a front mount cooler.. the way i drive will be normal and sumtimes give it a lil squirt...

Edited by geraus
Link to comment
Share on other sites

he already stocks the Germon Castol product. Thats the best.

On PerformanceLub he stocks Castrol oils but is this the German version or the Australian version?

All the links point to the American sites so I really can't tell.

Just deciding between Mobil1 and Castrol at the moment for my oil change for an R33 GTR. This will be the first change since it left Japan so I have no idea what oil it was previously running.

Link to comment
Share on other sites

On PerformanceLub he stocks Castrol oils but is this the German version or the Australian version?

All the links point to the American sites so I really can't tell.

Just deciding between Mobil1 and Castrol at the moment for my oil change for an R33 GTR. This will be the first change since it left Japan so I have no idea what oil it was previously running.

The Castrol ones he stocks are German he said last time i spoke to him. Shoot him an email he is quick with a response.

Im going to order some Mobile1 0w-40 from PerfoemanceLub... might order enough for two oil chnages. Thats around 10 bottles right?

Yeah 1 quart is .946 ml i think, so you would need 10 for 2 oil changes to be safe. I use 4 and bit bottles when i do an oil change on mine. I over fill it a little also.

Link to comment
Share on other sites

On PerformanceLub he stocks Castrol oils but is this the German version or the Australian version?

All the links point to the American sites so I really can't tell.

Just deciding between Mobil1 and Castrol at the moment for my oil change for an R33 GTR. This will be the first change since it left Japan so I have no idea what oil it was previously running.

its German Castol..

I have a few bottles. GC has performed well for some time on the oil forums though UOA...suposed to top notch.

The mobil1 and castol he sells is great stuff cant go wrong with either IMO

Link to comment
Share on other sites

its German Castol..

I have a few bottles. GC has performed well for some time on the oil forums though UOA...suposed to top notch.

The mobil1 and castol he sells is great stuff cant go wrong with either IMO

Just a minor clarification, Castrol 0w30 is made in Germany, 5w40 is made in America for the European market so its probably the same thing, I'm probably going some Castrol 5w40 and some Redline gearbox oil for the cars first change :thumbsup:

Edit: Picked up the oil in person from performancelub.com, excellent customer service and him and his business partner really know there oils. Saved me a little on postage :P

Regards,

Gareth

Link to comment
Share on other sites

Motul 8100 5w-40 synthetic- its pretty damn good, was on mobil one but noticed 0 oil pressure at lights one day then oil warning light came on had to turn engine off quickly- this doesnt happen now oil pressure is where it should be , at idle and at rev

Link to comment
Share on other sites

Motul 8100 5w-40 synthetic- its pretty damn good, was on mobil one but noticed 0 oil pressure at lights one day then oil warning light came on had to turn engine off quickly- this doesnt happen now oil pressure is where it should be , at idle and at rev

It got nothing to do with engine oil brand, 0 pressure can only mean mechanical fault, probably loses sensor cable or connector. For a oil to reach 0 pressure, it had to sheared below 10wt or less, not likely for a synthetic oil.

Edited by Trex101
Link to comment
Share on other sites

Hi,

Two questions, I bought Redline MTL for my R33 GTR gearbox oil. I've just read more carefully that most people are using MT-90, is MTL ok to use?

Should I ask if its possible to exchange for MT-90 (which would be hard because I have to get it back there first :D)?

I also need to do the diff oil and the front and rear of the car appears to have LSD's.

I'm looking at Redline 75w90 from http://performancelub.com.

But the Redline oil finder http://www.redlineoil.com.au/oil-finder.asp, recommends '80W140', which I haven't seen around at all.

Would you recommend using 75w90 in GTR diff's? The front is aftermarket and has a clunk when changing gears, I am not sure if the rear is factory standard or not.

I also found this post: http://www.skylinesaustralia.com/forums/Re...il-t190062.html

Which is slightly different again and does recommend 75w90 for GTR LSD's, I'm confused.

Regards,

Gareth

P.S. I am trying out the Castrol 5w40 in the GTR engine.

Link to comment
Share on other sites

Hi,

Two questions, I bought Redline MTL for my R33 GTR gearbox oil. I've just read more carefully that most people are using MT-90, is MTL ok to use?

Should I ask if its possible to exchange for MT-90 (which would be hard because I have to get it back there first :D)?

I also need to do the diff oil and the front and rear of the car appears to have LSD's.

I'm looking at Redline 75w90 from http://performancelub.com.

But the Redline oil finder http://www.redlineoil.com.au/oil-finder.asp, recommends '80W140', which I haven't seen around at all.

Would you recommend using 75w90 in GTR diff's? The front is aftermarket and has a clunk when changing gears, I am not sure if the rear is factory standard or not.

I also found this post: http://www.skylinesaustralia.com/forums/Re...il-t190062.html

Which is slightly different again and does recommend 75w90 for GTR LSD's, I'm confused.

Regards,

Gareth

P.S. I am trying out the Castrol 5w40 in the GTR engine.

IMO RL 75w90 would do just nice for your rear. The cluck from the front can either be due to mechanical problem or lack of correct friction modifier from the fluid. A good LSD load fluid like light weight shock proof would normally do the trick(can use RL LSD Fluid), MTL (70w80) would give very good shift & protection for syncro but would not cure your "cluck" noise which i suspect it's from the after market LSD. It's really difficult to advice you which fluid will work or not as we don't even know what type of after market LSD is in there.

I would advice you to try the likeliest solution first, try and error.

Link to comment
Share on other sites

IMO RL 75w90 would do just nice for your rear. The cluck from the front can either be due to mechanical problem or lack of correct friction modifier from the fluid. A good LSD load fluid like light weight shock proof would normally do the trick(can use RL LSD Fluid), MTL (70w80) would give very good shift & protection for syncro but would not cure your "cluck" noise which i suspect it's from the after market LSD. It's really difficult to advice you which fluid will work or not as we don't even know what type of after market LSD is in there.

I would advice you to try the likeliest solution first, try and error.

Unfortunately the cars straight from Japan so I also don't know what LSD is in there.

So MTL is ok for a GTR gearbox?

I will try 75w90 in the rear, and look at some redline lightweight shockproof for the front, should I go redline lightweight shockproof in the front without the LSD modifier? Or do I need to add the LSD modifier?

The only thing I know about both LSD's is they seem pretty damn tight and the car is pretty heavily modified from Japan so I'm not sure if it was just street use.

A mechanic has advised that the whine and clunk are from the front LSD but it is "operational".

Link to comment
Share on other sites

Unfortunately the cars straight from Japan so I also don't know what LSD is in there.

So MTL is ok for a GTR gearbox?

I will try 75w90 in the rear, and look at some redline lightweight shockproof for the front, should I go redline lightweight shockproof in the front without the LSD modifier? Or do I need to add the LSD modifier?

The only thing I know about both LSD's is they seem pretty damn tight and the car is pretty heavily modified from Japan so I'm not sure if it was just street use.

A mechanic has advised that the whine and clunk are from the front LSD but it is "operational".

Depend on how's your shifting now, if it feel notchy and difficult in engaging, then the MTL(70w80) would work better then thicker 75w90 oil as the thinner oil will squeeze out faster from the syncro thus promoting quick positive shift. RL lightweight shockproof & 75w90 gear oil do already contain LSD additives, the amount of additional LSD additives to add will depends on the level of LSD noise(how tight or losses is the LSD).

There's no real answer to your question, it's more of an educated guess with trial and error thing. I would suggest you add a quart of 75w90 to your front with remaining MTL and see what happens.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • People still have Skylines? I thought they're non-existent now. 
    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
×
×
  • Create New...