Jump to content
SAU Community

How Much Is It Worth?

i ruv u skyrine
 Share

Recommended Posts

i ruv u skyrine Rookie

i ruv u skyrine

Posted
Posted (edited)

Hey everyone.

figured it more appropriate to post this in here as im not actually putting this up for sale (yet).

on my 180 ive got a trust GTR spec cooler (with twin cooler inlets). im thinkin bout downgrading to a single inlet because i suspect i might be losing a little bit of response due to the forked piping to accomodate the twin inlets, and because of the fact that i cant fit a reo bar because the piping gets in the way.

ive been told by a few reliable sources these are fairly sought after amongst the GTR crowd and worth a fair bit, but noones really been able to tell me how much i could expect to get for it.

600x300x70 tube n fin

anyone got any idea how much i could expect to get for this thing?

Edited by i ruv u skyrine
Link to comment
Share on other sites
DAN00H Mentor

DAN00H

Posted
Posted (edited)

G'day mate

hard thing is that a lot of good coolers are now available for cheap prices. Yes, your trust is a good unit and originally would have pulled good coin. I'd say you could possibly get $800 if it's in reasonable condition they were about $1500 new. truth is most people don't need a huge expensive IC for anything under 450rwkw

good luck mate :)

Edited by DAN00H
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • pogman
      George's R33 GTST build

      By pogman · Posted

      Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • GTSBoy
      Hello Everyone

      By GTSBoy · Posted

      They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • Triple OG
      Hello Everyone

      By Triple OG · Posted

      I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • r32-25t
      GReddy Injector Help!

      By r32-25t · Posted

      Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
    • Dose Pipe Sutututu
      GReddy Injector Help!

      By Dose Pipe Sutututu · Posted

      You can just get the injector bosses, which allows top feeds to fit. He can use the same injectors without issue, like these (another option): https://rocketindustries.com.au/af59-2210-rb25-fuel-injector-inserts     The Racework ones look a bit better: https://www.nzefi.com/product/raceworks-lower-injector-mounting-boss-kit-for-r33-rb25det-s14-s15-sr20det/   You could also just get a similar kit like the Radium one by Plazmaman: https://plazmaman.com/product/nissan-rb25det-r33-billet-fuel-rail/?srsltid=AfmBOoogfYq49X0fu2Wdbf8yOf6zt9egyPAif_gn3Qr3G8hzAphhTgOkO70  
×
×
  • Create New...