Jump to content
SAU Community

Recommended Posts

Haven't come across a similliar thread like this, definately believe it's a good idea and am keen to learn more! Will be very interesting to see different driving styles relative to tire, power, suspension and drivetrain options.

Il start with my compilation;

(This is what I find that works for ME and MY car)

I've had the car for a good 16 months now, attending a handful of track events and the more then common hill run I've learnt a fair bit and have progressed well. Adapted my driving style to suit the car and it's set-up.

Car 93 R32 GTR with HICAS

Power 240kw @ 1 bar, light diet; stripped boot

Handling Toyo T1r (front), Toyo proxy 4(rear), Tein adjustable coil-overs, green stuff pads

-learn the car.. Know what the car is, how it puts power down, brakes, turns, any tendencies it has... The simple basics..

-Make sure the car is up to the task at hand! Brakes have friction, critical temps, tires are healthy and warm.. It's not a touring car you won't be able to keep performing at 100% lap after lap. When driving always leave room for error I stick to the 80-90% rule

-Once you commit the power into the turn DON'T let go, use the throttle to your advantage adjusting the cornering lines trajectory with your feet rather then hands

-understeer is easily enough corrected with power or smooth lift off/ brake (prefer the power ).. unless your going warp speed then your screwed. :D ..... Slower in faster out, front heavy gtr is prone to understeer.

-Many people turn in too early and are then forced to tighten up the corner on exit. Make the corner as open as possible, you will carry more speed and reduce tire scrub ultimately spending the least amount of time in that corner.

-Brake in a straight line, my car has hicas (removing in the future) I find that the car wiggles under hard braking from the weight transfer. Do not trail brake unless you REALLY know the car, if you are forced to trail brake get back onto throttle gently asap (pending on car's direction ofcourse) to transfer the weight back into the rear.

-When linking turns be smooth, give the attessa time to work and keep the weight balance as neutral as possible keeping the car flat, power on/ brake progressively. When possible use the transfer to get out of sticky situations. Weight transfer in my opinion is very over looked! Try strapping yourself into a 4 point harness and attack the twisties, it's much easier to feel what the car is doing and where the weight is going as your are basically moulded into the fixed seat.

-Use the right gear! If you max the gear mid corner don't change (you dip the clutch, car goes from max power to 0 for a split second when grabbing the next gear. Brutal way to unbalance the car)

***end of dribble drabble**

Cheers Tomek!

Edited by Tomek
Link to comment
https://www.sau.com.au/forums/topic/225946-your-tips-on-skyline-tarmac-driving/
Share on other sites

Interesting thread. Will be good to see the difference between the skylines (32,33,34) but as always each driver will attack the course in their own way.

So far i have not had time to get to the track but hope to change that soon.

-Many people turn in too early and are then forced to tighten up the corner on exit. Make the corner as open as possible, you will carry more speed and reduce tire scrub ultimately spending the least amount of time in that corner.

Totally agree. Taking the turn a little later and swinging the nose around helps reduce understeer. Once the weight is settled and the nose feels lighter (than turning in early) mashing the throttle is more controlled and effective and throws even more weight to the rear as the corner exit is taken.

Early turn-in makes it harder to use the entire corner. The line is sharper and more weight is thrown on the front left/right wheel. This becomes an issue when tackling the apex. Late turn-in is more an "aim at the apex" method IMO, it's more balanced.

Ditto on that tip there Snowy, one of your best :P

I'm going to try not to produce a bunch of drivvle here on, but one of the best pieces of advice I once receieved from Gentleman Jim was to try gearing up, ie, stay a gear higher than your brain is telling you, using the torque and not revving the tits of it.

I used both methods at Winton on Sunday, and when using only 3rd and 4th gear for the entire circuit it was consistently approx one sec a lap quicker than raping it in second gear for the tight stuff.

It's a method that transfers well over to tarmac rallying as well, and the car will thank you for it :wave:

  • 3 weeks later...

you can't learn to drive on a web forum. what do you want us to tell you? brake as late as you can, get the apex right while holding as much corner speed as the car is capable of, and get on the gas as hard and early as possible - simple really

lol.. :D:rofl: bunch of jokers ey..

you can't learn to drive on a web forum. what do you want us to tell you? brake as late as you can, get the apex right while holding as much corner speed as the car is capable of, and get on the gas as hard and early as possible - simple really

Im not asking for tips for myself, but rather interested in hearing about people's different driving style.

Not as simple as you word it, or else everyone would be running fast times.

Use the grass, there is miles of race track out there that people don't utilise!

Bloody oath. Don't be a girls blouse. Don't just clip the apex kerbing with your unloaded inside tyres. Do it like a real man & stuff all four wheels over the kerbing and take as much grass as you can with you. :D

The cornering sequence is simple.

Brake (if you must).

Turn in.

Nail that kerb.

Get some air.

Get some grass.

Get some serious chassis/tarmac spark interaction when you rejoin.

Edited by djr81

Slow is smooth.. smooth is fast..

Use the warm up laps to get into the rhythm.. start off slower with the focus on being smooth.

Find the limit by steping over it. A race track has run off areas for a reason..

I'm going to try not to produce a bunch of drivvle here on, but one of the best pieces of advice I once receieved from Gentleman Jim was to try gearing up, ie, stay a gear higher than your brain is telling you, using the torque and not revving the tits of it.

Good tip :wave:

I drive on tarmac much the same as I do on gravel.

A lot of fast entry sliding and late braking. Carrying max speed through the turns anyway possible to try and make up for my huge lack of power!

Plus, the car is actually setup for gravel so to get the best time out of it on the black stuff you have to be a bit aggressive and slidey.

In a car with good grip I agree with slow is smooth.. smooth is fast tho.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When's the rear mounted turbo kit coming? Needs dose and V8 chop idle lol.
    • I was very unimpressed with how the car came up from the A pillar forward, before I hit things (twice). It all has to go. It had to go, but now it has to go... more. So we finally found the very first Shennanigans with the entirely perfectly setup engine that had no problems being pulled apart to improve on 'was perfectly fine'. Cam bearings looked a bit... stock. Which isn't entirely bad given they were stock and this is a ~20 year old engine. So new cam bearings are on the way because it's somewhat difficult to get to this stage to do it later, and it will trash the block. It was quite unusual that it wasn't done when the perfectly new-looking VCM cam was originally installed by [unknown] What IS unusual is the cam that was installed there was advanced SIX degrees. As to why there is no way to know.. however it could have been @Dose Pipe Sutututu's mate who wanted a larger cam sound but also wanted it to come on earlier to be more usable. This is my dyno sheet with the previous setup - This cam is not supposed to peak until 7000+ RPM, according to VCM. This is what lead me down the whole 'my heads/intake setup is running out of puff and can't support the cam' line of thinking to begin with. Anyway too late now - New cam is in! It could be rather funny if this smaller cam acts like a larger cam because it isn't advanced six degrees. In the spirit of everything is working amazingly - the COMP cam required no dialling in whatsoever. It was about 0.5 degrees advanced, which seems pretty bang on. Any adjustment either way would be further out. I'm told as a chain breaks in it ends up regarding back about 0.5 a degree as the chain breaks in, making it bang on. In the spirit of everything was previously working amazingly - The timing gear that was taken out turned out to be was an N-Motion double timing chain kit, with adjustable cam gear (which is how it was 6 degrees advanced) and all looks entirely perfectly new. It also had a Torrington bearing, which was one of the reasons I ended up getting the Cloyes kit which they used in the C5R 24 hour racecar - Because I couldn't confirm what was in the engine when talking to Tony Mamo. I did believe however it was a Double chain kit of some kind... but found no supporting documentation or evidence for it.
    • I recently did this to my R33 with the full set from Car Mats Direct, they can't do the vinyl anymore that's advertised on the website due to a supplier issue so I ended up with the Black Loop Pile which looks great. I went all out with rubber sound deadening sheets from Repco and also added the sound deadening foam layer option with the carpet. Makes a world of difference and got rid of all the weird smells in the 29 year old interior. It was a bit of work but I'd 100% recommend it, Car Mats Direct had awesome customer service and quick postage. Replaced my seats with some sporty ones from Autotechnia while I was at it, feels like a new car.
    • Got the motor out and torn down. I'll be dropping off the block Monday. Luckily the scoring on Cyl6 is much less pronounced then the pictures made it out to seem. It can barely be felt. If you pass your finger over it 10x you'll barely notice it. Hopefully by some chance it will only require a honing. I'm not in the mood to buy one size larger pistons or another block. Oddly enough my 6th cylinder with the scoring has extremely clean intake valves compared to my other 5 cylinders. I'm worried the scoring was caused by too much fuel or Water/Methanol washing the cylinder. I'll review some old logs to confirm.  This was also the first time I pull an engine with the transmission still attached. It went much better then expected. I was worried my CD009 wouldn't make it easy due to its sheer size but it was much easier this way. 
×
×
  • Create New...