Jump to content
SAU Community

Carbon Bonnet Series 2 R33

The BOP

By The BOP,
in Exterior & Interior Styling

 Share

Recommended Posts

KISIN Veteran

KISIN

Posted
Posted
We have just received stock of these S2 bonnets. We trial fitted it onto our demo car and it fits very well and makes the front look very aggressive, no to mention providing extra cooling, especially over the top of your ignition system where it is needed most.

+1 for the pic of that bonnet on the car.

  • 2 weeks later...
baron25 Proficient

baron25

Posted
Posted (edited)
No these are not ADR approved, I have been trying to speak to someone about what is required for ADR approval but am yet to find anyone that can give me a clear answer or the right person to speak to. Can anyone help me here?

Talk to Blits Bodykits in QLD, they went through the whole process and now have ADR approved bonnets and guards, they could probably point you in the right direction.

http://www.blitsbodykits.com.au/

Edited by baron25

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      I have one and it was at ~43.5PSI.
    • GTSBoy
      RB20DET lean on cold start

      By GTSBoy · Posted

      Put a pressure gauge on the fuel rail.
    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      I've uploaded logs / the current map to Gdrive if anyone has any ideas. https://drive.google.com/drive/folders/1FPnr22Z-EilG7tYdHSi0Qb07P2jfFLKV?usp=sharing
    • luke gtr
      Spotted on the street....

      By luke gtr · Posted

    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      I'm running a Haltech Platinum Pro with the stock map for the RB20DET + tweaks for my build. When I started it this morning, the IAT was at 32F/0C (Outside temp was ~42F) and the AFRs went off the scale for my AEM gauge. I let it run for ~30 seconds then turned it off. I then did a smoke test, by hooking into a vacuum line directly behind the throttle body, and confirmed there was no leaks ( i let the smoke tester run for ~5 minutes / confirmed it was generating smoke before hand ). I then started the car again, after fixing a power steering leak.... and it seemed to be happy for ~30 seconds (was at ~11/12), but then seemingly shot back up to ~18 again. I then let the car run for a few minutes, thinking this was just cold start related, but the AFRs never came back down. I didn't let the car fully warm up, so maybe this makes sense, but I'm not sure what to do? The AFRs, when I last ran it, were normal, but because of personal reasons I haven't been able to break in the car. It was rebuilt last year. Engine / Mod list: Supertec pistons Spool rods Kelford 270 cams and Springs Stock crank Deatschwerks 900cc injectors Walbro 255 (Wired directly to the battery relocated in the trunk) NKG Audi R8 Coil packs + Conversion Harnesses from Wiring Specialties Holset HY35 turbo Haltech Platinum Pro ECU Haltech boost controller (wired in for high boost RB25 Neo transmission + needed bits for the speedo to work  
×
×
  • Create New...