Jump to content
SAU Community

Timing Belt

gfunkk

By gfunkk,
in General Maintenance

 Share

Recommended Posts

(OO)SKYLINE(OO) Grand Master

(OO)SKYLINE(OO)

Posted
Posted
^ nice post mate i was scratching my head for ages wondering about the "12th year"
That makes sense...
LEGEND!

Hehe!!

No worries, all good!

I must thank HPI Magazine to help me understand how to work it out.

All this just to know what year the timing belt was replaced... They could have just wrote April, 2000... LOL!

:P

reNEGaDe88 Proficient

reNEGaDe88

Posted
Posted (edited)

Yeah I thought it would have been 12/4 as in December 2004 @ 63k. But the engine has 100k on it now. So I needed to know if its been done. The waterpump and gasket look 40k old, not 100k old. So that makes sense.

But yeh, big thanks. Saves me ~350$ , don't have to do it for another 60k, now that I know. Timing belt won't be likely to instantaniously snap and blow up the engine anytime soon...

Edited by reNEGaDe88
(OO)SKYLINE(OO) Grand Master

(OO)SKYLINE(OO)

Posted
Posted

Yeah they say change it every 100,000 km's.

So since its was changed at 63,155 km's, you won't need to change it again till 163,155 km's.

Yeah your timing belt will be fine. But you can always check to see what brand they used...

I bought my car at 113,000 km's, 1990 model and had a Nismo Timing belt.

There was no date when it was changed or any stickers, so to be safe I just changed it to a Genuine Nissan Skyline R32 GTR Timing belt as you can be safe with that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Neil's R33 Gts-t Build

      By Dose Pipe Sutututu · Posted

      Let's hope that's not a copy pump either. There were so many copies of them back in the day.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Damn it, I was at work last night, and stayed in a room there during the storm with the car outside, but undercover, I just went downstairs and well....there was a large steel locker that has come from some place last night, it wasn't anywhere I could see yesterday, and yeap, it landed on the fraking car....of course it did..... LOL So, I'll need to take it back for paint and panel, luckily it was only the boot that took the hit, so it could have been worse Serves me right for staying at work and getting on the cans with some of the boys
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, really happy with how it all turned out As for aftermarket lip, nah, I'm not really a fan for practically reasons on a street car that gets driven everywhere  I did have the full lower kit on my 2015 STI, but found the front lip scrapped alot, even at stock 4x4ish ride height As the NC sits now, with the lowest point of the car at 110mm, so just legal, some steep driveways and steep speed humps will still "just" scrap those little plastic OEM air dam thingies on the undertray just before the front wheels
    • Dose Pipe Sutututu
      Hypergear Turbochargers and High flow Services Development thread

      By Dose Pipe Sutututu · Posted

      Here's one I help build and tuned a decade ago, Garrett  GTX3071R Gen 1, T3 twin scroll 0.83 rear housing. Went from larger 272 cams down to smaller Tomei Poncams to help with the low end. S13 non VCT motor. Car was purpose built for the track, hence low down was the focus. Note the actual dyno chart shows lower boost, however the EBC and boost gauge showed 1.9Bar (Ignore the torque, I was young and didn't know how to set derived torque)  
    • hypergear
      Hypergear Turbochargers and High flow Services Development thread

      By hypergear · Posted

      I’m doing some side developments on SR20det S13 engines, its one my hobby cars used it to compare flow capacity of some smaller size wheels. SR20det is one of another JDM legendary engines I'm sure there are plenty of SR enthusiasts on this forum, I will share results some common turbo configurations here. a quick run down of what the car is: Wide body 180sx Type X with black top engine (blue). It has: Stock bottom end Haltech 1500 ECU 5-0 motorsports trigger kit Kelford SR20DET Beehive Spring with Titanium Retainers Kelford Cams SR20DET S13 188-B 268/272 Cams G25-660 Turbocharger in T2 .64 rear housing internally gated ARP Head studs MLS head gasket 1000CC ID injectors Walbro 450L Fuel pump Front mount cooler kit JJR’s 3 inches turbo back exhaust (its too short for the 180sx it had to be extended) Pump 98 fuel Hub Dyno tune So far made 270rwkws at 22psi full boost by 4500RPM. Engine is very knock limited hence a pretty bad looking top end. From previous experiences it seems like SR20dets are happier with bigger size turbine, some thing like a GT30 would make way better top end, but on same time response is lost. It won't be a problem with S15 VCT engines. I'll be testing alternative turbine housing, turbine wheel and possibly dump pipe options for extra flow to resolve the problem and of course E85 would resolve all the issues.            
×
×
  • Create New...