Jump to content
SAU Community

Recommended Posts

hey guys got a skyline turbo has intercooler and everything needed to give it 368hp at the rears, ill cut to the chase. when i accelerate hard then change gears white/greyish smoke pours out the exhaust, but only when i change gears not while im accelerating or even idleing. the car use to run like a dream then i blew an intercooler pipe and drove around with it busted for about a week (silly i know) i got it fixed but it hasnt run the same since its alot more sluggish now. the power use to be instant now its sluggish till the boost comes in then it picks up. plz help. dont know what to do.

Link to comment
https://www.sau.com.au/forums/topic/226643-white-smoke/
Share on other sites

hey guys got a skyline turbo has intercooler and everything needed to give it 368hp at the rears, ill cut to the chase. when i accelerate hard then change gears white/greyish smoke pours out the exhaust, but only when i change gears not while im accelerating or even idleing. the car use to run like a dream then i blew an intercooler pipe and drove around with it busted for about a week (silly i know) i got it fixed but it hasnt run the same since its alot more sluggish now. the power use to be instant now its sluggish till the boost comes in then it picks up. plz help. dont know what to do.

sound to me mate like u done the turbo oil seal?, also could have over spun the turbo wheel damaging the bushes or bearing cartiage. wasn.t the car a pig to drive with out the cooler pipe connected???? white smoke bad= burning oil, dark smoke good= just exces unburnt fuel. what type of turbo and line is it??

Link to comment
https://www.sau.com.au/forums/topic/226643-white-smoke/#findComment-3990326
Share on other sites

Blue smoke is generally more an indicator of burning oil. White smoke can be just condensation. Grey smoke is carbon build up generally. While you were driving it with the pipe busted, you have probably carboned up the exhaust nicely with all the over fueling due to less volume of intake air but the same amount of fuel. If it was the oil seal on the turbo you'd think it would be blowing smoke under acceleration aswell wouldnt you? None of this really explains the lack of performance though. Well besides perhaps stuffed plugs after driving it for that long with the busted pipe and over fuelling? Its all hypothetical but things to check out none the less.

Good luck mate,

Deren

Link to comment
https://www.sau.com.au/forums/topic/226643-white-smoke/#findComment-3992601
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Means something is not set up right, tune/calibration related.  
    • Finally replaced the previous temporary mesh indicator surrounds (temporary was the last 10+ years 😂) with a 3D printed GTR style version for the front indicators. I think it looks a lot nicer than the old setup and at least the indicators now point in the correct direction rather than angled off. Needed a little bit of tweaking to deal with the intercooler piping but got there in the end. Old and new photos below. 
    • It's weird to me that you say this because I'm pretty sure locals with relatively standard standalone tunes (boost/barometric compensated alpha-N) still have driveability issues when they pop intercooler hoses. Maybe with enough data I can just train some kind of model that spits out an expected grams/cyl given every sensor input except MAF like what FCA did with their Pentastar 3.6 ECU logic. Basically stock everything. The main motivation honestly is to have a sensor that can be a decent baseline source of truth. In scenarios you're describing obviously it won't work every time but it seems to me the number of corner cases that exist in MAF load is maybe not as severe and difficult to manage vs ITB alpha-N with some MAP/barometric compensation.
    • What are your plans for your blow off valves? Purely plumb back? How soft will the spring in them be? AFM can be tricky to get super smooth and nice, especially depending on the rest of the system, and then can be very easily upset if something slightly changes. IE, even if you run recirc blow off valves, you could still see issues getting it to behave at certain load points as turbos might start to spool, but you release the throttle but it's not enough pressure to crack the bov open to recirc, and you can end up with reversion which can cause double metering, and hence dumping of fuel into the system, and stalling the engine.   If you're going to run a map sensor for closed loop boost control from the ECU, what makes you want to keep the AFM?    
    • It's not bad, it's just not flexible. And say if you have any leaks between the MAF and plenum, well then your load axis goes out the window. Here's a real world scenario, I blew off an intercooler hose last track day, as the clamp decided to Bluetooth itself somewhere. Still continued to do 2 laps and drive it to the pub for a couple of beers then home. Good luck doing that with a MAF setup 
×
×
  • Create New...