Jump to content
SAU Community

17" Rays Engineering Wheels + Bridgestone Tyres

phatlavish
 Share

Recommended Posts

phatlavish Mentor

phatlavish

Posted
Posted

Item: Set of 17" Rays Engineering wheels with Brigdestone RE-01 tyres

Age: Unsure

Condition: Good

Price: $800

To Fit: 5x114.3

Location: Sydney

Contact: Pm or reply here

Set of Rays Engineering 17" wheels: 17x8 front & 17x9 rears with a bit of dish, i'm unsure of offset. They were on a R33 gts-t with bolt on wheel spacers (i'll throw them in for free) on the front so they could clear the calipers

Tyres are Bridgestone Potenza RE-01 with loads of tread left- around 80%. unfortunately one of the tyres has a small screw in it, but it still holds pressure fine

post-35556-1215324109_thumb.jpg

  • 3 weeks later...
  • 1 month later...
  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • DRoc81
      Shifting questions

      By DRoc81 · Posted

      This was a huge help.  We followed the steps,  although shifting into 2nd was actually into 3rd for us,  and 1st was into 2nd ( steps 9 and 11) .  The long flash was the 4th flash.  So shift solenoid A is possibly the culprit.  Is this inside the transmission itself? Or is it accessible by just front the pan? Or is it bolted to the outside of the transmission?  Thanos for your help everyone
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      Can you enlighten me on your best practice regarding these hoses? I don't wanna make the same mistake if you already got a better solution.
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      I have some silicon hoses already, for example engine to watercooler. But yeah, I get the sentiment. The lower intercooler silicon hose is drippy too, despite not being very old. Does anyone except Nismo make these same lines out of rubber? Long term I think they'd be the better replacement, especially since the car won't live as hard a life anymore as in the past nor be driven as often.
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      I know most issues are just age related. But for example the turbo oil drains, there is dash adapters for these and you can just make a braided teflon line for them and (probably) never have them leak again. Also not terribly expensive. Can you even get the factory hardlines from new? Or are they repairable if they break?
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      I know it'd be much much easier with the tool. I hope I can find one that won't take 3 weeks to get to me an isn't a "Asian models kit" that has tons of (to me) useless adapters for a load of cash.   It's a summer project/fun car. I do wanna enjoy it, without endless downtime over and over. So yeah I would even go and buy an engine crane + stand to save myself the trouble of hard to reach or unreachable places going bad later on. Would also be a good opportunity to put on a Fluidamper, renew the mains seals and stuff like that. I have some money on the side that I can use for that, what I wouldn't want to or be able to do is let everything be done by a shop or have my engine completely rebuild right now. I intend to do most of the "doable" jobs myself. Pulling an engine can't be that hard, can it?
×
×
  • Create New...