Jump to content
SAU Community

chrome intercooler piping ?

DJ_L3ThAL

By DJ_L3ThAL,
in Victoria

 Share

Recommended Posts

DJ_L3ThAL Grand Master

DJ_L3ThAL

Posted
Posted

hey guys, i wanna get my intercooler piping and possibly the intercooler if its possible brogutn up super chromed like the show cars and get those blue pipe hose attachments so its all looking schmick.. will i need to buy piping or can i take off my system adn take it somewhere to get it done ? and how much roughly am i up for ?

cheers

Link to comment
https://www.sau.com.au/forums/topic/22698-chrome-intercooler-piping/
Share on other sites
predator Grand Master

predator

Posted
Posted

If you want to just get it coated.. look up "electroplating" in the yellow pages.. but i doubt it would last because of what ppl were saying.. mild steel can rust. I've heard chromed piping can start to rust on the inside if you get it dipped - which can be a problem and probably not that noticeable until its too late. Otherwise u might be just be better getting all new stainless steel piping like Megs was saying.. which u can polish right up.

For the blue stuff, you just need those silicon sleeves, which you can probably get some made up.. i know HKS and crap supply them with their cooler kits, so you must be able to get them around.

I'm just thinking of that 200sx at MAS with the Gold chroming everywhere - that was awesome. Not sure about long life though :)

Risto Enthusiast

Risto

Posted
Posted

hehe lemme cmment bout this one trust me chrome does rust i got it on my cooler piping and my battery started to leak and i noticed it when my cooler piping started to rust... the hose you can get from purple pig rubber hose supplys :D its basically a rubber hose no matter what colour it is get the good stuff its about $1.50 1cm i think so yeah good luck u might as well polish mild steel then chrome it it cost cheaper bcz theyll both rust anyway itll be bout $150 all your pipes stainless steel is the way to go mate i made that mistake dont make it aswell as i always say you get what you pay for

DJ_L3ThAL Grand Master

DJ_L3ThAL

Posted
  • Author
Posted

i spoke to a local shop and they didnt wanna know me :D

like would an exhaust shop be cheaper than say ice performance and the likes ? as i'd prefer ice to do it coz i trust them etc but i mean its only piping, as long as its made without holes/weak spots etc it should be kool yer ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Sean'O
      3D printing fun

      By Sean'O · Posted

      Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 😑. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
    • GabsReDeal
      R32 GTS (RB20DE) clogged cat

      By GabsReDeal · Posted

      Hey everyone, This is my first post apart of the introduction. I tried searching a bit on the forum but couldn't really get a straight answer. I got the car to my mechanic as I felt it being weak. It seems that it was missing on two cylinders due to the injectors. I had all my injectors clean and the car runs much better. The mechanic also confirmed my suspicions that the cat is clogged and needs to be tackled asap. The cat rattles a bit and the hot exhaust warning frequently lights up when driving after getting the injectors clean. In my introduction I was asked about what modification I might be interested in and mentioned a cat delete. From what I was told, this is not really beneficial on the RB20DE and there are more cons than pros.  Could perhaps anyone give some suggestions on what the best course of action would be since the current cat is toast and needs to be removed/replaced anyway? I can also sometimes smell a strong smell of fuel, but I'm not sure if this is related.
    • Milkmun
      NC MX5

      By Milkmun · Posted

      Hope the cans went down well at least 
    • Milkmun
      Neil's R33 Gts-t Build

      By Milkmun · Posted

      255 can't go wrong with the price.
    • Kinkstaah
      Neil's R33 Gts-t Build

      By Kinkstaah · Posted

      When I was replacing my pump due to being stranded in the wrong state, I went with the Deatschwerks 320lph kit. It is a direct plug in to the stock wires, harness, everything. It comes with a plug... but you can plug the OEM plug directly into this thing. https://justjap.com/products/deatschwerks-dw300-fuel-pump-nissan-s13-silvia-r32-r33-r34-skyline-c34-stagea?currency=AUD Downside: Won't actually flow that much on boost if you want to push it on E85, but it's comparable to the 040/255 etc. Little more actually.
×
×
  • Create New...