Jump to content
SAU Community

Power For Skyline R34 Gtt Auto

TrentR34

By TrentR34,
in Western Australia

 Share

Recommended Posts

TrentR34 Explorer

TrentR34

Posted
Posted

Hi Guys

I got some stuff done to my skyline during the week. FMIC, 3" Cat back zorst, High Flow Cat, 3" Dump pipe,Bigger fuel pump, Apexi air induction, Apexi Digital boost controller and then I got the Nistune to 0.9 bar of boost. I was reading in some old topics that people with same car (R34 gtt auto) same stuff done to there car and they were getting 173wrkw at stock boost. And at 0.9bar of boost I got 158wrkw. Is this the power you would expect from a R34 gtt auto?

Trent

Link to comment
https://www.sau.com.au/forums/topic/227476-power-for-skyline-r34-gtt-auto/
Share on other sites
rice boy Collaborator

rice boy

Posted
Posted (edited)
Yes the car was tuned yesturday by Hyperdrive. They used Nistune to remap the ecu.

They were saying that it was the first R34 there to use the software.

hmmmm..

doesn't sound right..

not 158

hey sell that car and buy mine. :whistling:

Edited by rice boy
Levi_ Proficient

Levi_

Posted
Posted

Does sound a little low, though Hyperdrive do seem to have a reasonably accurate dyno (as in it tends to be lower than some) but that wouldn't be that much of a factor.

My manual R33 GTS25t managed 190rwkw with similar mods (though my boost curve isn't great).

Post up your dyno sheets and maybe we can figure it out.

DRFT31 Experienced

DRFT31

Posted
Posted (edited)

Hi mate,

I have a 1998 nissan skyline gt-t auto sedan, mods are fmic, turbo back exhuast 3inch, greedy electronic boost controller, k&n pod filter. Car on 10.5psi made 189.5kw, and stock boost which was 8psi made 183.3kw. Mind you this is with std fuel pump and std comp. This is the safest level to boost a 34 running a stock ecu. As if you go past the 12psi mark they usually start to cut out thats how the std ecu's are designed. Your figures don't seem right, i would be expecting a little bit more power. Post the dyno sheet up if possible. Hope everything goes well

Cheers.

Edited by DRFT31
TrentR34 Explorer

TrentR34

Posted
  • Author
Posted

I would post a picture of the dyno run but last night when I was at a mates house, I was about to leave so I started the car to warm it up then and it was running for about a min then it just turned off. So I tryed to turn it back on but it wouldn't start, so I waited for about 15min came back the car started for about 30sec's this time and I couldn't get it started again so. wtf :) . So now the car is stuck at my mates house and I will need to take it back to Hyper Drive to fix it. O yeh and the Dyno Sheets are in the car so I can't get them.

Levi_ Proficient

Levi_

Posted
Posted
Hi mate,

I have a 1998 nissan skyline gt-t auto sedan, mods are fmic, turbo back exhuast 3inch, greedy electronic boost controller, k&n pod filter. Car on 10.5psi made 189.5kw, and stock boost which was 8psi made 183.3kw. Mind you this is with std fuel pump and std comp. This is the safest level to boost a 34 running a stock ecu. As if you go past the 12psi mark they usually start to cut out thats how the std ecu's are designed. Your figures don't seem right, i would be expecting a little bit more power. Post the dyno sheet up if possible. Hope everything goes well

Cheers.

Where was the dyno done for yours, I'd be suspecting that your numbers are a fraction high.

Dani Boi Grand Master

Dani Boi

Posted
Posted (edited)

I dont understand, I thought you lose around 30% of power from the fly through drivetrain in his case 158kw making thats 211hp at the fly making that around 150rwkw....

On my dyno sheet i got 270hp at the fly i dont have 270rwhp...

Edited by Dani Boi
Magic Experienced

Magic

Posted
Posted

It doesn't just depend on what mods you have bolted on, what about the condition of the engine?

And judging from what you said how the car wouldnt start properly before. I think your plugs might be fouled or ro0ted. Might be responsible for a proportion of the power loss? m2c.

thrtytwo Veteran

thrtytwo

Posted
Posted

34 GTt's are 206kw flywheel stock (take about 7 or 8 kw for auto so ~198kw) and i dont think you would lose that much to the wheels without any mods. so with those mods its definately low. Did u get ur car from ur mates yet ??

bubba Grand Master

bubba

Posted
Posted (edited)

You don't lose a percentage, a drivetrain will sap a certain amount of power but that doesn't increase with power.

158rwkw does seem rather low. I made 183rwkw with a similar turbo on the same dyno.

If a tuner is giving you a dyno sheet reading flywheel horsepower yet it's a chassis dyno, it's just a guess. Ask for one at the wheels.

Edited by bubba

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      IMG_8641.mov     She doesn’t sound the best but starts with out using any gas now. I just ran some injector cleaner through her. started roughly the first time after adding it but gave it the beans slowly upto 4k, Must have cleaned a few cobwebs out. another step in the right direction for the sub
    • Kinkstaah
      R34 Diff oil

      By Kinkstaah · Posted

      Sadly I can confirm if you are actually seeking to drift, you will quite easily spin up one wheel. Even if you're going in a straight line. I am not entirely sure of the metrics/terminology here but there's only a certain amount that the helical will actually spin both wheels. I've seen it on video with my own car where two lines of smoke switch over to just one after you really get in to it. Unlike with a clutch diff where you can keep your foot planted until the car regains grip, in my experience with the helical you want to be utilizing traction control allowing LIMITED slip or lifting (partially) when you start to spin up both tyres with a Nissan helical. Which makes them pretty sub optimal for drifting duty. That said... this is probably a helical on numbers alone. Just put the Kazz in
    • GTSBoy
      Short shifter r34

      By GTSBoy · Posted

      Let's just fix the problem by f**king the rest of the gearbox.
    • GTSBoy
      R34 Diff oil

      By GTSBoy · Posted

      Unlikely, as per Greg's post. This is not helical diff behaviour unless one wheel is up off the ground. Shimming what? You don't "shim" a mechanical LSD. Probably not in the sense that you have heard of people "shimming" a diff. And the process that Nissan f**kwits call "shimming" a diff involves super-preloading a VLSD cartridge against the side of the diff to create a friction/wear point (in a place that it wasn't supposed to have one) to make the sloppy, useless, viscous diff into a hybrid viscous/mech abortion. In case it isn't clear, I consider the process to be stupid. Nike.
    • Duncan
      Short shifter r34

      By Duncan · Posted

      How much does the shifter move when the car is in gear with the engine off? If it is more than about 1cm you need to replace your shifter bush. Your shifts will just get crunchier, not faster, with a short shifter unless you also rebuild the whole box
×
×
  • Create New...