Jump to content
SAU Community

Recommended Posts

Hi All,

Hoping I could get some advice. I have checked the forums and kind find anything relevant to my situation.

Last night I absolutely thrashed my R32 gts-t for about 15-20 minutes. My younger brother then gave it a go and revved out 1st gear many times. This morning, driving to work I noticed the following problems.

1. 1st - 2nd gear change grinds if done quickly. Difficult to put it in if done slowly.

2. slight shudder when pulling away in 1st (slowly).

I tested it again at lunchtime, the shudder seems to have dissapeared, however the 1st-2nd problem is still there.

I doubt the gear oil has been changed in a while so I have it booked in tomorrow. If this does not alleviate the problem then I assume the syncro between these gears will need to be adjusted. Any suggestions/advice?

Thankyou

Edited by Tristan21
Link to comment
https://www.sau.com.au/forums/topic/227511-possible-syncro-issues/
Share on other sites

LoL

The shudder could have been from the clutch friction plate. You could have overheated it, which's then made it slightly unbalanced. That could explain how it went away after driving for a while.

Do a g.box oil change, if you know its been a while - go from there.

LoL

The shudder could have been from the clutch friction plate. You could have overheated it, which's then made it slightly unbalanced. That could explain how it went away after driving for a while.

Do a g.box oil change, if you know its been a while - go from there.

Thanks mate

Shudder will be from the clutch, and it sounds like you shagged 2'nd gear synchro. It might work better with fresh oil.... might not. If not, better off fixing sooner rather than later, because it will just damage the selector sleeves and cost you even more money. R32 GTST boxes are cheap compared to R33/R34/GTR, so probably the quickest option would be a second-hand box from an importer.

Well I have changed the gear oil to a synthetic, seems a little better but still not perfect. Any idea how much a 2nd hand gearbox will go for?

I also had the clutch replaced, shudder is now gone.

Thanks guys

When you get your gearbox oil changed, check how much metal shavings have been collected on the magnet at the bottom of your gearbox, this will determine how much thrashing you are giving your gearbox..

I recently changed my gearbox fluid at home with a mate, and i discovered 3 clips attracted to the magnet, my mate reckons they look like linkage clips, whatever they may be, its not good, even though i still can change gears smoothly, i get grinding in 3rd and 4th gear when flat changing..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jamie does know his stuff , you might just want to give them a call and ask - here is their FB page  -  https://www.facebook.com/profile.php/?id=100063506985512 - you will find the number to call them on.
    • Do you think the guys in Penrith are install the E85 Kit?
    • Thanks Pac!   I will reach out to them!
    • Yes, but 2 things of the top of my head, 1. Legalities of nitrous on a street car. 2. No chop chop. I fully understand that there's much cheaper ways to make power, and whilst a wet 50 shot is fairly cheap to install, bottle fills are expensive, and bottles always need to be refilled, and nitrous also has its own inherent issues with reliability, and tuning, from my experience of others using nitrous, it doesn't take alot to lunch a engine real quick if something goes slightly wrong when spraying, if I wanted a big chunk of additional powers, a spooly boy would make alot more sense, disregarding the additional engineering, supporting mods and other logistical issues of sticking a spooly boy on a car that came naturally aspirated from factory  In the end I'm not racing for sheep stations, and I don't really care if people make more power, or are faster than me, or spend less, or more than me, the only thing the car needs to do is drive around and make me smile, which it is doing now Really, I just want a shiny new intake to look at when I'm cleaning the engine bay, and of course, some more induction doorts, and maybe even that 5kw for that elusive 200hp cherry on top that I might get If the FAB9 intake plenum, TB and air filter box thing doesn't eventuate for whatever reason, Plasmaman do one, not as fancy looking, and a fair chunk of more cash is required when including the TB and other bits and pieces that are required to install it, but, it is another option that is available to me if FAB9 one does fall down (but I really, really.....really, want the FAB9 one though) TL;DR. You want what you want
×
×
  • Create New...