Jump to content
SAU Community

Recommended Posts

Yesterday driving home i went to take off at the lights semi hard, reved to bout 2k and released clutch and took off, first gear reved to bout 5k, into 2nd got up to bout 3k n the car violently shuddered, not just a flat spot like a fuel pump overload. It sounded like the car was boosting but didnt have the power. i drove home the rest of the way not reving over 2.5k n trying not to boost it up. Worked fine. Just took it for a drive to work out the problem. It was fine in 1st gear but in 2nd, 3rd n 4th after about 3000 revs it shuddered violently again. It similar sound n feeling to when you bunny hop the the car not having the revs up when releasing the clutch (like learning to drive manual). The car has only a manaul bc which is set to about 11psi. Every thing else is stock. Anybody know of what the problem may be.

Link to comment
https://www.sau.com.au/forums/topic/227816-car-shuddering-violently/
Share on other sites

violent shuddering happend to me once when a coilpack went out and the car was running on x amount of cylinders

could be coil pack, spark plug or injector etc or mayb something is blocking a particular cylinder in the plenum

I took off quick, didnt dump the clutch. I honeslty cant tell if its drive train related or not. I changed the spark plugs 2 weeks ago, gapped to 0.8mm. The shuddering sound comes from the back of the car but it feels as though the problem starts in the front of the car, engine related. If it was the clutch, wouldnt it just free rev? There isnt any clutch smell.

feel the engine on idle for any shudders, then rev with your fingers on the tb and feel again.

if there is, try pulling a coil pack out one at a time to see if there is any change in engine note,shuddering. if you pull onw and there is no chnage then that cylinder is probably not firing properly

this happnd to my beema, i ended up finding the bad coilpack n changed them all.

and as i drove it, 1st n 2nd gear didnt shudder but at 3rd when the engine was on higher loads, the engine was out of balance and vioently shuddering.

might not b the prob but it was for me so jst offering input.

I took off quick, didnt dump the clutch. I honeslty cant tell if its drive train related or not. I changed the spark plugs 2 weeks ago, gapped to 0.8mm. The shuddering sound comes from the back of the car but it feels as though the problem starts in the front of the car, engine related. If it was the clutch, wouldnt it just free rev? There isnt any clutch smell.

Mmmm shuddering @ the back, but feels like it's starting in the front.

So something that runs from diff to engine, gearbox and tailshaft. Check universal joints, when they're on the way out it feels like all hells breaking loose from front to back. You will be able to get them checked for free at most brake/clutch/suspension type places if you don't know what to look for..So if it's not the prob no loss :bunny:

Edited by madbung

My assumption was that all skylines have a small idle shudder, the revs bounce up n down a little but not enuf to show on the tacho, mine does that n has for the last 2 years that ive had the car. The car had a minor surge under power a few weeks ago so i changed the spark plugs and that seemed to fix it, untill y'day. Ill pull them out 2moro and have a look at them to see if any of them are rooted. I think ill give everything that i can clean a big clean as the engine bay is fairly filthy at the moment.

The thing is in the last few months ive a had a heap of little bugs go wrong in the car such as i have something draining the power from my battery that an auto elec couldnt find, this surging before i changed the plugs, my drivers side window switch is knackered so putting the window up n down i have to twist some wires together n reverse them to make it go up n down, then they all touched the other week n now the drivers window wont work at all, i think ive blown the relay. 6 week wait n 400 bucks for a replacement part from japan. Ive just saved up enuf money to do a heap of engine mods but now ill have to use this money to get this other stuff fixed. The car is playing up with me n its hard haveing a nice car that doesnt work properly, my fiancee is getting pissed of with me cos every week it feels to her there is a new problem with it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • She swallowed the spider to catch the fly.
    • Half anticipating the next question then: I have two magnets stuck in my oil pan. What should I do? 
    • If it's magnetic what is stopping you from using a magnet on a thin wire from fishing it out?
    • Those 2 solenoids in that assembly I mention, are the PWM solenoids for torque converter lock-up clutch & EPC (line pressure control) ~ when most folks hear of 'solenoid failure', the tendency is to think electrical failure...but fact of the matter is, especially wrt the EPC solenoid (which is moving/running all the time), you can have an electrically 'good' solenoid, that's absolutely broken/worn out mechanically inside...ie; valve plunger return spring rubbing against spring retainer plate, lowering preload pressure.. ...and the solenoid armature extension limit spring wafer with bad wear/broken off petals... ...and if there's ever been any metal flying about, damage to the valve plunger end itself... ...the stuff one never really sees, unless you go the whole 10yards trying to answer the question "why is my line pressure screwy, but TCU isn't flagging any EPC solenoid fault?"...and carefully dissect the solenoid. Worst (and most probable) scenario is when the plate spring petals break off, they get held by the magnetic flux, get mashed up by the armature into little bits, which end up in the space between the armature & shading core bore, and things get stuck or randomly jam up, and your line pressure goes flat and doesn't change...and the TCU never sees it, as it doesn't actively monitor LP... ..then it gets into insidious land, if you end up with lower than expected line pressure...lets say high clutch..and the lower pressure causes it to slip ~ when I say 'slip', think say 2000rpm on the drive plates, and 1800rpm on the driven plates, because the slip is making them under-rotate by 200rpm ; you get all the usual nasties like heat and band/clutch wear, but even if it's only 20rpm slip the same thing happens...and... you'll hardly ever pick this up driving the thing with the torque converter active as it effectively masks these sorts of slippages that are line pressure related ...(the newer TCUs can detect clutch slip rate)...just  FYI as it were...  
    • There's nothing that some paddle pop sticks and extra cable ties can't fix.
×
×
  • Create New...