Jump to content
SAU Community

Recommended Posts

For those of you who don't know i just picked up series 2 1999 stagea it came with adjustable teins not quite sure which model yet but while the compliancer was doing the roady he found the rear shocks were seized and could not be adjusted the car is stupid low in the front but have been adjusted up to legal but the rear sits lower now cos of no adjustment . I was wondering anywhere in melbourne to get these repaired or can i buy tein rear only from somewhere? Any help greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/228062-seized-teins/
Share on other sites

Thanx for the directions guys found a tein authorised repairer 40 km's from my house which is f$%kin rare when your in central vic, but then again bendigo is the hoon capital of Victoria more cars seized under the new hoon laws than anywhere else in vic not bad cosidering they have a population smaller than geelong. :)

Link to comment
https://www.sau.com.au/forums/topic/228062-seized-teins/#findComment-4013580
Share on other sites

so the shocks aren't seized, it's just the height adjustment?

Any mechanic with half a clue and a set of C spanners should be able to sort it if he has some decent penetrating oil or a big enough hammer.

Yeah just the hieght adjustment part of it

That was my thought but APPARENTLY they will not budge obviously they dont have enough wd40 and big enough hammers in their workshop LOL :)

Link to comment
https://www.sau.com.au/forums/topic/228062-seized-teins/#findComment-4013662
Share on other sites

Well A)I cant get them out myself B) It needs to be done for roadworthy and the compliance shop cant do it. So in order for me to pass roady and get plates the height of the rear needs to be lifted since the jap owner had it stupid low and now it's seized in that position which is about 80mm of the ground.

Link to comment
https://www.sau.com.au/forums/topic/228062-seized-teins/#findComment-4016757
Share on other sites

Well A)I cant get them out myself B) It needs to be done for roadworthy and the compliance shop cant do it. So in order for me to pass roady and get plates the height of the rear needs to be lifted since the jap owner had it stupid low and now it's seized in that position which is about 80mm of the ground.

If its just for roadworthy you've probably got more chance taking the springs out of the car and working on them.

My compliance shop was going to throw away my Ohlins coilovers (ie. >16 way adjustable and good spring rates) because they told me they were "rusted out" (sand blasting fixed the surface rust).

Link to comment
https://www.sau.com.au/forums/topic/228062-seized-teins/#findComment-4018343
Share on other sites

im not sure which state u are in, but height adjustable shocks that allow u to lower the car below stock are against ADR's, they are not legal but u might be able to engineer them which counts for something in some states.

also not to mention the spring rates, im not 100% on this but i beleive u can only increase the spring rate by 75%, im sure someone can correct me if that figure isnt right. AFAIK the teins are a touch below this, even the aus spec ones.

Link to comment
https://www.sau.com.au/forums/topic/228062-seized-teins/#findComment-4022030
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sorry no - The sandtrap adventure ended the day, happened at the end of the last session. At that time I wasn't hearing any weird noises nor were the brakes shuddering anymore. It was only when watching the videos that I remembered I had these sounds early on!
    • Did the noise appear after your sand trap adventure? Could be something got dislodged and is playing rub rub. Even a rock wedged somewhere.
    • Is there a shroud around the tailshaft spline into the back of the box? They can rub and make a horrible noise if they are not on straight/damaged. The heat might have caused it to grow too much in one direction and rub.
    • Strangely I noticed it either disappear later in the day, or not be present. I definitely noticed when I was crawling around that open wheel thingy entering the pits (that part was audible in car). Driving home and commuting around town for example, I didn't hear it. It's plausible that it was a brake disc or something still slightly in contact. The brakes absolutely felt BAD for the first couple of sessions, huge amounts of shudder and grinding as they got up to temp - And then I actually just forgot about it as the day went on/didn't notice it. The videos were from the morning when this was more present than the afternoon/drive home when it wasn't. I've asked around and got a variety of responses including handbrake shoe contacting hub, CV joints, CB tailshaft bearing as above, and clutch input bearing. I didn't test if it disappeared when clutch was in. I haven't noticed it in any of the other videos nor did I notice it when driving to that extent. More or less hoping the microphone at the rear license plate giving some kind of clue of 'something' but it looks like "spin stuff and see if you can notice it" is the way forward here. I could be smart and use the gopro mic and re-mount it to that location to see if the sound is still present at low speed actually. Sounds like a decent test whenver I have the CBF'ness to drive the car again. Given it's almost 40C for the day of the track day and the next 3 days after, the CBF is high. All I've done since getting home is unpack the car, remove the remnants of the lip and undertray and left it there. I was surprised how well the PMU Club Racers actually worked. The brake performance on the track was absolutely fantastic, best I've ever personally used, no fade whatsoever and the bitiness was almost too good, I was scrubbing more speed off than I needed to, but I also ended up infield when I started trying to scrape off ... less speed.... so...
    • Not really, no. Anything you would do is easily reversible.
×
×
  • Create New...