Jump to content
SAU Community

Recommended Posts

in the morning when i turn my car on..(infact anywhere where the car has been sitting for more then 30 mins off) theres a ticking comming from my bay, but only at around 2500>3000, not when its idleing, i pop the hood to find its comming from the front of the block, on the right side (turbo side) of the rocket cover when i rev it.. after driving for about 10 mins it goes away, what the hell is this..is it serious? thanks for reading :) car: R32 GTST 1992

Link to comment
https://www.sau.com.au/forums/topic/228428-weird-stupid-noise-heeeeeelp/
Share on other sites

Skylines and engine bay noises, do search...

When were your timing belt idler and tensioner pulley's last replaced? I've had this issue, I reckon i was a few weeks away from a seized bearing, overheated and snapped timing belt :)

Sure its not your injectors? If you race the motor, does the noise disappear on the decel? What oil and when was it changed last?

Regardless, poke about the engine bay with a long screwdriver on your ear.

i change oil every 3000k's, it started actually after switching from valvoline to caltex synthetic oil....timing belt changed at 93 000ks, its done 132 000 now..

lol sorry i tryed search b ut came up with similer issues but not the same, it ticks only wen i accelerate,, then it goes away completely... its perfect at idle..

Edited by SXCR32

Check your starter. There is a thing called "the clicker" it is known as this because, well, it clicks. When you start the car it should click for about... oh, I would say 10 minutes max when running. Normally it is out of 2nd gear as well because the engine is warmer. Then the clicking is better on warm days etc. That could mean a bad starter. That is why they make it like that. X__X;;

Happend to me and I ignored it, then I got stuck in the middle of nowhere.

Just something to ponder mate.

If this IS the case, don't replace it. It can be repaired for like 25$ easy. Take it to a shop is all.

Edited by AKW

since it was after a oil change i would also have to go with a lifter. get this a bit at work. when you change the oil and put a new filter on you induce a fair bit of air into your engines oil gallerys which can enter a lifter pretty easily, usually it will go away after a bit of driving. if not, lifter could possibly be on its way out...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes correct. Also, I'd avoid applying it to soft paint (however I doubt you'll ever have to deal with it in practice). So any paint that hasn't fully hardened, could be a 1k paint that never fully hardened or it could be a 2k paint that was laid down thick and hasn't yet fully hardened. 
    • Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
    • I recently purchased a 2018 Infiniti Q60, which has an SD card navigation map. I can see my system has options for real time traffic updates etc, and am wondering if there is something I can purchase to get this working? I can see there are at least updated maps for USA and Canada, but nothing for Australia. Surely Infiniti took changing road systems and city expansions into account when they decided to use an inbuilt navigation over Android Auto/Apple Car Play, or are we doomed to drive on streets that don't exist in the navigation system if you drive to a new area?
    • Luckily I didn't put in etch primer as I just found out it's not compatible with my body filler lol. Also just need to sand the panel anywhere between 150-400 grit so I'm in the clear there. It does say to not apply to soft old paint, I assume that means paint that is flaking, peeling,etc
×
×
  • Create New...