Jump to content
SAU Community

Recommended Posts

anyone know what the hose running from the intake pipe closest to the jay pipe to the back of the power steering pump is for ? some days i seem to have vairing degrees of feel to the steering . appears to get heavier when driving spiritedly and quite light when just cruising . any thoughts ?

99 RS four S

Edited by lachlanw
Link to comment
https://www.sau.com.au/forums/topic/228725-vairable-power-steering-assistance/
Share on other sites

consider a power steer fluid cooler, sounds like the fluid is heating up, changing its viscosity, creating the heavy steering feel. Most of the Skylines are fitted with a small tube one, our cars were not designed be thrown around as much. Not sure what the hose is, also consider changing the fluid, i use transmax Z in my PS, found it gives a lighter feel and handles the higher temps better. Ive been planning a PS cooler for a while now, ill get round to it soon.

there may be easier and less messy ways, but the way I do it is, 2 hoses on bottom of resovoir, one is fluid return, other is fluid out. Place towel under resovoir, unhook return hose, (dont ask me which one is which ?) need to plug up hose connector on bottom resovoir immediately to stop it draining, use same diameter piece of hose with tight bolt in other end. I then extend this return hose with another piece of hose and a hose connector so you can feed it into a waste container. get new fluid ready, have mate turn on engine and make sure resovoir starts draining, if not then you prob have wrong hose, once nearly empty start filling resovoir, keeping a good fluid level, have mate turn wheel side to side a few times. Once drained fluid colour changes to new fluid, stop, reconnect, check level. Go for drive, check level again.

had my cover off today and there is a line running from the afore mentioned intake pipe to what looks like something similar to an oil pressure sender unit its on the line coming out of the power steer pump. has another line coming off it that is dissapears down by the block . and by heavier steering i mean it has more feel and need to hold on tighter . by no means is it heavy heavy

Edited by lachlanw

On series 2 neo (not sure about s1) there is 2 pipes connected to the power steer pump.

One line connects the the intercooler pipe which runs between the intercooler and the throtle body.

There is a second line which runs behind the timing belt cover and connects to the inlet plenum near the fuel reg

I had mine disconnected for a while when I fitted the fmic as the kits do not come with the extra nipple in the intercooler line

To be honest I did not fell much difference, but I did only drive it for a few hundred k's like this. I then fitted a new nipple to the intercooler pipe and hooked it up again.

It most be reading boost pressure, so when pushing the car, ie on boost, there must be a change to the power steer feel by operating a pressure relief solinoid on the back of the pump. That is my guess.

The one I've been driving is noticeably heavier on the highway/at higher speeds than it is around town, in fact its very light at low speed. This is consistent too. Surely it must have some sort of variable assist?

yerah i agree with you guys aye . sometimes if you are taking off during a 3 piont turn ie taking off while on full lock and give it a bit of boost it has real heavy steering but goes away straight meh . i like it how it is tho . seems to be set up at a farily good ratio for how i like my steering . two hands when you boostin it and light as when cruising on thw high way

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update: I got the magnet out. I bought 3 different flexible magnetic reach tools, but none of them worked. The magnet on the tip was all less than 2lbs of force, so i had to buy a special cylindrical magnet that had a pull force of 9lbs.  The magnet finally came in the mail yesterday, so i got under the car to get to work. The super strong magnet isn't that long, so i only have about 1 finger pinch lengths to hold it. I was so scared when i was going in the hole, that the 9lb magnet would just fly away inside the oil pan never to be seen again, but i had my butt cheeks clenched and finger gripped on that thing so tight, i managed to get it to suck the other magnet out.  It was a victory for me last night.         
    • Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
    • You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
×
×
  • Create New...