Jump to content
SAU Community

Recommended Posts

hey guys,

its not really a problem but i just want to know why and if i can fix it,

when i put the pedal to the floor say in 2nd you can hear the turbo spooling up and boosting but the car just feels like its holding back,

but when i only put my foot down half throttle the car boosts a lot better,

do i have a leak somewhere? or too much fuel to the engine?

mods are:

RB20DET

greddy fmic

3" front and dump

bosch 040

cheers,

Kyle

Link to comment
https://www.sau.com.au/forums/topic/228982-boost-issues/
Share on other sites

i may suggest plugs.

I had the exact same problem in my rb20. Car went better at half throttle rather than full throttle.

At full throttle the car seemed to be holding back and misfiring.

So i say change plugs and gap to .8mm. Clean coil packs with contact cleaner while your at it to.

Cheers Adrian

Link to comment
https://www.sau.com.au/forums/topic/228982-boost-issues/#findComment-4028356
Share on other sites

Mate I had the same problem with my 33 a few weeks ago, I had the timing set at RE customes and the car goes much better.

I can only run factory boost though as soon as it goes above 9 psi it retards and looses power.

I was told that if I get a pfc it would be fixed completely.

*edit.. I have the same mods on mine.

Link to comment
https://www.sau.com.au/forums/topic/228982-boost-issues/#findComment-4028544
Share on other sites

engine management system like a apexi power fc tuned correctly should fix it

everyone and there pfc its a nearly stock car dumb ass.

yeh check plug gaps, and look for splits in any of the silicon intercooler pipes had a 32 gtr with the a similar problem when he put the boot into it there was a split that would open up and let the boost out but when putting the booting into her slowly it would open up.

and its a real bitch to find to you have the squeez the pipes for it to show.

Link to comment
https://www.sau.com.au/forums/topic/228982-boost-issues/#findComment-4028665
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have one and it was at ~43.5PSI.
    • Put a pressure gauge on the fuel rail.
    • I've uploaded logs / the current map to Gdrive if anyone has any ideas. https://drive.google.com/drive/folders/1FPnr22Z-EilG7tYdHSi0Qb07P2jfFLKV?usp=sharing
    • I'm running a Haltech Platinum Pro with the stock map for the RB20DET + tweaks for my build. When I started it this morning, the IAT was at 32F/0C (Outside temp was ~42F) and the AFRs went off the scale for my AEM gauge. I let it run for ~30 seconds then turned it off. I then did a smoke test, by hooking into a vacuum line directly behind the throttle body, and confirmed there was no leaks ( i let the smoke tester run for ~5 minutes / confirmed it was generating smoke before hand ). I then started the car again, after fixing a power steering leak.... and it seemed to be happy for ~30 seconds (was at ~11/12), but then seemingly shot back up to ~18 again. I then let the car run for a few minutes, thinking this was just cold start related, but the AFRs never came back down. I didn't let the car fully warm up, so maybe this makes sense, but I'm not sure what to do? The AFRs, when I last ran it, were normal, but because of personal reasons I haven't been able to break in the car. It was rebuilt last year. Engine / Mod list: Supertec pistons Spool rods Kelford 270 cams and Springs Stock crank Deatschwerks 900cc injectors Walbro 255 (Wired directly to the battery relocated in the trunk) NKG Audi R8 Coil packs + Conversion Harnesses from Wiring Specialties Holset HY35 turbo Haltech Platinum Pro ECU Haltech boost controller (wired in for high boost RB25 Neo transmission + needed bits for the speedo to work  
×
×
  • Create New...