Jump to content
SAU Community

Recommended Posts

I have been having issues with my car going into R&R mode I installed a PFC recently and had it tuned (unigroup), now what I have noticed is two tings my car now has a hesitation/pause, almost light somethings cutting the power this comes every now and again I think its always been there but its only noticeable with the power FC (don't think its in the tune). My knock reading on the power FC will go as high as 112 but the engine light does NOT come on at all. I think this hesitation/pause has always been there, but possibly the tune has made the hesitation more noticeable. Its seems to only do it on light acceleration. And the knock reading wont go above 38 at any other time. I am thinking the fuel pump is on the way out???????? Also the engine light attached to the power fc knock system is set at 60 is there a way to check its on/set at 60. Any suggestions?????

Link to comment
https://www.sau.com.au/forums/topic/229196-strange-hesitationpause/
Share on other sites

First up, I'd talk to Yavus about what he thinks about your hesitation, as he clearly would have noticed it.

What turbos have you got - surge maybe?

PFC's don't have RR.

112 knock is bad, don't do it.

Datalogit / power excel to check the knock flash setting.

Fuel pressure gauge should show a f.pump weakness.

Edited by GeeTR

I have std turbos, I know Power Fc don't have R&R it was doing it on my std computer it just wasn't noticeable (cant think of any other reason I was having R&R too coincidental) and sometimes it will have this hesitation and not read any knock ???? i would have thought Yahulz would have picked it up as well but they wouldn't do a power run on very light throttle and its intermittent, and as I said the power fc is not reading knock and showing me on the dash light as I have never seen the engine light come on. Dont have datalogit. yeah i should give him a call but i dont think its got anything to do with his tune its an unrelated problem but he is the man to see. its just miles away from where i live.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah. "New pump" does not have to mean "massive pump".
    • Well, can you still get an OEM pump, and by the time you're buying a Nismo/N1 etc, just buy another aftermarket pump. It's better to have the pump able to flow more if its needed, than for your pressure to drop off. At any point in time, you're replacing the oil pump in a rebuild. Aftermarket pumps are likely going to be a better economical choice, and they don't have any negatives, even if they can flow more.   Also, when you're saying "replace the pump gears" are you meaning leave a 25+ year old housing in the engine with unknown wear, and just put new gears in? As that sounds silly to me, especially if you do have that minute amount of wear, that means your new pump gears now have a little bit more clearance beside them, which means, whelp, you may not get to build a lot of oil pressure or make a lot of flow.
    • Right, but if you replace the pump gears + put a spline or sine drive gear on the crank on a Nismo/OEM/N1/etc pump at that point do you really still want more flow/oil pressure? Let's say this is a the aforementioned "keep it simple" build, no more than ~400 kW at the crank.
    • Strength. And on the early RB26, full engagement of the pump drive.
    • I really don't understand the point of aftermarket oil pumps if your particular engine doesn't need more oil pressure. As far as I can make sense of it the problem seems to be cavitation from sucking air, maybe the pump gear design with how it interfaces with the OEM crank, and maybe the backing plate screws wanting to loosen themselves. How does flowing more oil fix these issues?
×
×
  • Create New...