Jump to content
SAU Community

Recommended Posts

Hi everybody,

I bought my gtst with all the basic mods and its power fc which was tuned for 100 octane petrol. The previous owner says it was tuned on a shell petrol which didnt have ethanol in it (not V-power racing which i dont like as its 20c more), so my question is since if run i it on 98 octane is there something i should adjust on my hand controller to accomodate to the lower octane petrol?

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/230188-r33-tuned-for-100-octane/
Share on other sites

Hi everybody,

I bought my gtst with all the basic mods and its power fc which was tuned for 100 octane petrol. The previous owner says it was tuned on a shell petrol which didnt have ethanol in it (not V-power racing which i dont like as its 20c more), so my question is since if run i it on 98 octane is there something i should adjust on my hand controller to accomodate to the lower octane petrol?

Thanks!

Well you've contradicted yourself.

Tuned for Shell without ethanol means it was V-Power, the 98

The 100 was V-Power Racing, which had ethanol, and is not discontinued

So based on what you said, your car is already tuned for 98... so if you've been putting 100 in there, you've sadly been wasting your money.

So if you just muddled yourself and you indeed WERE tuned on 100, you will need to be re-tuned for 98. Simple as that

Yeah somehow the previous owner had 100 octane shell petrol in it for the tune, he said it didnt have ethanol in it but he may have been mislead. Who knows.

So a WHOLE retune is required to have the car running optimally?

I'd check the knock levels on the handset first, if the readings are OK, I wouldn't worry too much about it and just get it done whenever [the tune].

Sounds like the last owner didn't know what they were talking about [some confusion over fuels], so it could be that your tune is already OK as it is.

Suck it and see.............

Well you've contradicted yourself.

Tuned for Shell without ethanol means it was V-Power, the 98

The 100 was V-Power Racing, which had ethanol, and is not discontinued

So based on what you said, your car is already tuned for 98... so if you've been putting 100 in there, you've sadly been wasting your money.

So if you just muddled yourself and you indeed WERE tuned on 100, you will need to be re-tuned for 98. Simple as that

V-Power racing has been discontinued on the gold coast where i am and i suggest in many other places

this thread is redundant

100 octane is standard factory issue.

skylines from factory are tuned for 100 octane cause in japan thats the lowest octane they have....exept diesel obviously.

stick 98 in the tank and alter the timing the timing a couple of degrees.

Knock levels aren't too bad actually, i had some trouble with it before but i think the boost wasn't tuned correctly (liked to spike).

I switched from bp ultimate to normal v-power last week and i havent seen knock over 25.

I'll take it to the drags and see how i go.

Nizmonut, so i retard the timing by the odd degree?

in summer you will notice a raise in knock

Yeah thats definately true actually, summer was when i was having problems....

I'll let you know when i have time to do it, and we can sort something out, thanks for offering to help. (sick r33 btw :()

this thread is redundant

100 octane is standard factory issue.

skylines from factory are tuned for 100 octane cause in japan thats the lowest octane they have....exept diesel obviously.

stick 98 in the tank and alter the timing the timing a couple of degrees.

lol. that is a good one. 100octane is the lowest in japan. I'm sorry mate but that's simply not true. having been to japan many times, and driven cars in a number of different cities (tokyo, osaka, kyushu, chiba, saitama) I can tell you 100octane is pretty much the bees knees. hi-oku blend. regular unleaded there is like 94 octane. good fuel 98 or so, and yes they have hi-oku 100ron fuel too. but no factory car would be tuned un-able to run on 98 or even 96. this myth came about when high performance cars designed to run on 95 or 96 octane fuels were run on fuel in aus that at the time was 90-92 at best. things have come a long way since then and the gap between japanese fuel and australian fuel is not that great.

V-Power racing has been discontinued on the gold coast where i am and i suggest in many other places

Is United doing the same thing with their Boost 98?

Unless the car is tuned on the edge, running Vpower 98 fuel shouldn't be a problem. You will get more petrol into the cylinders compare to vpower racing and find that the car is alot richer. You will be down on power as well.

Have you try the freedom 98? It has 10% ethanol as well and is only 2 RON lower than Vpower racing. If knock reads higher with the freedom fuel then pull the timing back by a few degrees until knock reading goes back to normal.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wideband is worth setting up if only for tuning purposes. I would not mess with the ignition system unless there's a misfire. HKS crank trigger is popular out here for the relatively easily sourced Denso crank sensor, not a bad idea to install as well regardless of power level on a standalone. Boost leak test is worth thinking about. Oil pressure sensor tied to a fuel cut isn't a bad idea either. Getting the tune figured out is a good idea. Without putting eyes on it and getting under it there's no way for us to tell you exactly what it needs but most likely you're down to the last 10% that will make a big, big difference in how happy you are with the car.
    • Doing a refresh of my 33 and can see a few websites stating they sell the entire main carpet for our cars, but they all have generic photos which is fine, i understand they are custom made to order.  Just seeing if anyone has got it done or had any experience with this, as i would only want to do it if the fit and finish was as good as oem https://carmatsdirect.com.au/products/moulded-carpet-or-vinyl-for-nissan-skyline-r33-1993-1998-coupe https://knoxautocarpets.com.au/moulded-carpets/nissan/skyline/skyline-r-33-1993-1998/
    • Any plans for E85? If so, add flex fuel sensor.   I'd probably add in the sensors I mentioned above if the Link will support using them for engine protection. With water pressure, you need to be able to effectively set it that "If temp > X, and pressure = atmospheric, shutdown" as at running temp, you should be able to read pressure in the cooling system. If pressure suddenly disappears, it means the water went some where, and this is a quicker reaction than waiting on water temp to go up (Which, can take a little longer than you'd like, considering it now has to wait for hot air to heat it up) Oil pressure, Oil temp, both would be on my list too if you're looking to add sensors. Wideband O2. And at least one EGT sensor. If you're feeling deluxe, put in individual runner EGTs. Single EGT sensor is more so forget about a specific number, get used to "What is normal EGTs", and then keep an eye on it, if it starts going away from "normal" it's a sign something is wrong (Also, things like the tune can still start going out of spec, but EGTs may not show it, for example one injector starts running leaning, so ECU richens everything up, now 5 out of 6 cylinders are rich, and running cool, with one cylinder lean and running hotter, so it's not perfect) Then there is your other things to look at non sensor related, but you may have already done, or have underway, and that would be things like building a sump for more oil, and better oil control under high G-Forces (Cornering, brakes, acceleration). Basically, the above is worth looking/thinking about, if the ECU can do protective stuff with it, and you continue to use it how you are (Drive it to the track, thrash it, drive home, repeat once every 3 to 4 months)
    • Can also confirm these work a treat for most balljoints and bushes. If you have access to a big rattle gun, they make the job so much easier and quicker, compared to using a socket wrench or shifter on the c-clamp 👍
    • Its sort of street but got used for circuit sprints on account of I never drive it on the road because I dont have the time to spare. So it usage was sits around for months at a time then gets driven either 50 or 250 kms to the track followed by 20 laps followed by 50 or 250kms home followed by stuck in the shed until next time. So yeah neither fish nor fowl. Just dont want to break it on the track as a preference. Hence the fairly short sensor/mod list. Probably more worried about it pinging itself to destruction more so than anything oil related.
×
×
  • Create New...