Jump to content
SAU Community

Recommended Posts

Recently I've noticed a ticking noise sorta coming from the back left part of the engine bay. Someone told me they think its probebly noisey injectors, because when you rev it the ticking goes faster with the revving...

Would this be affecting performance, causing damage or anything else ? Should I get it fixed straight away, if so how much would it cost, roughly?

Could it possibly be something else ?

Also, how do you check to tell if the engine is running lean or rich, or is knocking and that the afm and o2 sensors are working right?

Thanks for any help !

Do search.

RB's make a lot of injector noise. Use the afore mentioned screw driver on your ear if a) you think one is nosier then the rest and b) its only just occurred.

If the noise goes away temporarily when the revs drop, after racing it, then its inj's.

Harm? If one partially drops out when your WOT @ redline, sure you could destroy a motor worst case.

Thanks for the input so far guys,

The noise is pretty consistent whether engine is cold or at temp. whether its just been raced, driven gently or just turned on.

Ive been quoted $455 to clean and service the injectors, seem fair ?

The noise is pretty consistent whether engine is cold or at temp. whether its just been raced, driven gently or just turned on.

Ive been quoted $455 to clean and service the injectors, seem fair ?

Hey,

"Raced"as in "free revved while at standstill in neutral" :) When the revs are dropping, from a "free rev" the ECU cuts the injector signal for a moment, you should be able to hear the difference.

I don't think Iv pad more then $100 to have 6 injectors cleaned and flow tested; that price must include removal / reinstall...? ouch

Edited by GeeTR
I don't think Iv pad more then $100 to have 6 injectors cleaned and flow tested; that price must include removal / reinstall...? ouch

geetr, ill check for the absence of ticking after a free rev. and if thats the case, the noise is definetly injectors.... good diagnostics.

Thanks everyone for the continued input, my babies getting a major service from a trader on here, so ill look elsewhere for a fairer priced injector cleaning.

I was told by the people who gave me a quote that they would be sonicated, which im almost certain means they would remove them. But how could they be cleaned without removing them (is that what you get for under 100 geetr?) ?

anyway, i think ive decided to let them tick for a few more months and see if it gets worse or better (unlikely).

anyway, i'm so impressed by the knowledge on this forum...

keep an eye out for more of my newbie questions....

[edit]

oh oh i got one !

can i put that crappy injector 'add to tank when you fill' cleaner you see in the servos through my rb25det ? (im leaning towards not but interested to see what people think)

Edited by Dannyism

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Consider a 35 too...
    • He's right ~ there is no 'magic' with stuff like this ... it is more likely that in the process of looking for the short, the loom/wire 'incidentally' got moved in the process, thus removing the short ~ now, that maybe a wire (in a loom) rubbing against the edge of some grounded metal, that's worn through the insulation, causing the (now intermittent) short to ground. If one wire in a loom has been damaged in this fashion, it's reasonable to presume that other wires beside it may have also be damaged, and now exposed...you can bet the green crusty copper corrosion will start... ...that'd be a pisser, Murphy's Law steps right in as GTS observes...but worse, something like that is easier to find when shorted...ie; unplug bulb and fuse, and put multimeter in continuity mode so you get constant beep, and carefully poke about hoping to find if some movemet of the harness stop the beeping.... ...it's still all a bit Arnie tho' ..It'll be back... 😃
    • Yeah, but knowledge of one wire's insulation worn through to short on earth implies the possibility of other wires doing the same. I had my power steering die, because the wire that runs to the solenoid valve on the rack runs in the same loom as the power wire for the O2 sensor. And when the O2 sensor/wire did something stupid and burnt part of that loom to death, the only indication was the shit(ter) fuel economy and the heavy steering. It took deep excavation of the looms in the bay to find the problem. Not wear through in that case, but similar shit.
    • Ah, I thought he'd wired it to one of the spare ECU inputs! Too long ago since I read that post, ha ha. I've been arguing with radiators, harmonic balancers, alternators and rust since reading it.
    • Correct. The ECU cannot read oil temp. (Well, I think it probably can in some situations. I did have the thought of potentially repinning the ECU when I was doing oil pressure). I am using this into the MPVI dongle, so that the MPVI dongle can read oil temperature. It is attached to a VDO gauge which is obviously calibrated to whatever curve the sender actually is using. This would be easy if I could setup a table of voltage to temperature like many sensors, but it appears I cannot do this and can only setup the transform rule which appears to be Input (voltage) x Multiplier, and add an offset. This to me means it MUST be linear. So it may be a complete waste of time wiring this into the ECU. The idea was that the MPVI3 has standalone logging. I wanted to use this instead of a laptop with serial cable (for wideband) for long datalogs. Given the wideband also has electric interference, I may never trust this either in a world where the serial wideband and the analog output wideband do not agree. Last time I did a trace I could see the two wideband traces follow each other, but one was a little leaner than the other. I plan on playing with voltage offsets and actually driving the thing to see how close they correlate. If they never correlate... then, well, maybe I'll never use either. Ideally I'd like to have the Analog wideband read ever so slightly leaner than the serial one, because the serial one is 'correct'. Tuning the car to be ever so slightly too-rich would be the aim. Not needing to have a laptop flying around in the footwell connected with cables is... an advantage. About the only one from the forced upgrade to MPVI3.
×
×
  • Create New...