Jump to content
SAU Community

Recommended Posts

Im not going to lie, i have very minimal knowledge of importing cars.

With that out of the way i have recently been trying to research the topic.

Im on the market for a new car with a total budget around 26k and initially not many cars that were in my price range grabed my attention locally.

Then i began looking at imports and have become quite excited at the prospect of importing a V35 coupe.

Iv checked multipule sites including J-Spec (Much talked about on these forums) Imports101, Prestige Motorsport ect ect

Prestige motorsport seem to generally be giving lower prices for a landed and complied v35. With many examples between 20 - 22k.

Can anyone advise me if they are reputable company or not? Would they be giving lower quotes for a bad reason?

These are a couple of recent examples they have showed me:

http://www.prestigemotorsport.com.au/modul...hp?StockID=4675

http://www.prestigemotorsport.com.au/modul...hp?StockID=4673

Both of these cars are estimated at under 21k landed + complied.

Im bassically wanting to know if Prestige are a reputable company?

Also if anyone has managed to recently import a v35 for 25k or less landed and complied?

Does 26k seem like a budget that can get this done? or am i dreaming?

I really appreciated any you guys can offer me.

Regards.

Edited by Kile

Please note that if two brokers are charging near enough to the same service fee then their landed and complied prices will be the same assuming they are quoting realistic prices with accurate exchange rates, shipping costs and compliance rates ... just to clarify, we under estimate the exchange rate because no banks give you the full wholesale rate advertised, we over alll slightly for shipping and don't list the absolute cheapest compliance price usually so there is a very good chance of it costing slightly less than the estimate as long as rates don't change heaps or any unexpected costs pop up ... also keep in mind that we have many customers looking for these cars who are signed up with deposits in place, so the best deals are always gone before they make it onto the website anyway.

With regards to your desired car, a budget of around $25,000 landed and complied should be very simple to get a good V35 these days, you should be able to fairly easily get one for around $20,000 to $24,000 as long as you are not looking for a 2006 model in black with 6 speed manual and Brembo brakes or a limited edition 70th Anniversary model ... the examples you showed above are fairly typical of what you can get from auction these days if you are an active client and bidding on cars, we have had a number around this price but as noted above they are all sold before hitting the mailing list.

I would be happy to also show you examples if necessary or actually help you find a car if you are ready to buy?

I'm currently going through Prestige Motorsport for my import, Geoff has been extremely helpful and informative. I'd highly recommend him based on my experience so far.

That being said, don't get me wrong, I have nothing against J-Spec. I've heard good things about Craig from friends who have been through the same process. It was just unfortunate that when I was ready to buy, J-Spec were going through a busy patch and couldn't get back to my query in time so I decided to go through Prestige.

I think with both of these companies, they'll be quoting realistic prices as it's not in their best interest to underquote. They gain their reputation through customer experiences and feedback and the only way to keep a customer happy is to be as helpful and accurate as possible.

Craig i really appreciate your detailed response. I am currently in the process of moving residence so i will be waiting a month or two before starting the process. Although i can say once i am ready to get the ball rolling you will be on the top of my list to contact.

UnCo thanks also for your informative and genuine post. Much appreciated.

:P

Kile

Oh, sh*t, too late...umm....

Please note that if two brokers are charging near enough to the same service fee then their landed and complied prices will be the same assuming they are quoting realistic prices with accurate exchange rates, shipping costs and compliance rates ... just to clarify, we under estimate the exchange rate because no banks give you the full wholesale rate advertised, we over alll slightly for shipping and don't list the absolute cheapest compliance price usually so there is a very good chance of it costing slightly less than the estimate as long as rates don't change heaps or any unexpected costs pop up ... also keep in mind that we have many customers looking for these cars who are signed up with deposits in place, so the best deals are always gone before they make it onto the website anyway.

With regards to your desired car, a budget of around $25,000 landed and complied should be very simple to get a good V35 these days, you should be able to fairly easily get one for around $20,000 to $24,000 as long as you are not looking for a 2006 model in black with 6 speed manual and Brembo brakes or a limited edition 70th Anniversary model ... the examples you showed above are fairly typical of what you can get from auction these days if you are an active client and bidding on cars, we have had a number around this price but as noted above they are all sold before hitting the mailing list.

I would be happy to also show you examples if necessary or actually help you find a car if you are ready to buy?

:P:( :(

My only advice would be bid at auction. That stock shown is usually sitting in a car yard, so the dealer has already bought the car at auction, put a mark up on it - then sold it to you.

For my next car - i'm going to Japan to find it.

Edited by paulR32gtr
My only advice would be bid at auction. That stock shown is usually sitting in a car yard, so the dealer has already bought the car at auction, put a mark up on it - then sold it to you.

This is true most of the time, but there are some dealers (well more export agents) who buy from auction and put only the standard FOB fee on top that you would be paying if purchased from auction anyway - this effectively saves you the time and hassle of checking dozens of cars to find a good one and then try to buy it cheap. They check out cars and bid low amount all day every day so the ones they get are the better cars at the better prices which are often better than you will normally get from auction ... this is only the case for the "good" agents but obviously these are far outnumbered by the dodgy ones who just want to make huge $$$

Also there are such things as wholesale dealers who offer us cars at below market value and then move them to auction if they aren't sold within a few days. These cars are normally cheap enough that about 75% or more of them will sell for more than the wholesale price if they end up at auction. This is just one more way that you can get a better deal without going to auction.

The reason I mention this is that there are a LOT of people out there who just don't want to buy from auctions, either they don't want to make a decision about bidding and budgets within hours of first seeing it with only a few photos on which to base that decision, or just want/need more information than can be obtained from auction cars in a given time ... these people really need to buy from dealers or other agents so they can get more photos and details and take a few days to decide on the purchase, so there are different options for different people depending on with they require to make them comfortable with the process.

For my next car - i'm going to Japan to find it.

This would also work if you are not looking for anything too specific, but if you are looking for a less common vehicle or combination of colours & features then you may not find it by restricting yourself to one city or region of Japan by being there in person ... often you can find the car you want more easily, faster and sometimes cheaper by being able to cover ALL auctions and dealers around all regions of Japan at once which can be done just as easily from your computer here in Australia as it can by being in Japan in person.

  • 1 month later...
  • 4 weeks later...
  • 4 weeks later...

geoff at prestige is the man he helped me for 5 months to find the right 1971 kgc10 skyline...it was worth the wait. he had around 30-40 cars inspected for me and scored me a gem. Help me thw whole way through the process. I still email him now for a chat.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You're not wrong, but more than a few times I've heard of people running into issues where their injector characterization isn't quite right and that approach works for that specific configuration but once they switch over to a new set they discover a whole bunch of stuff wasn't set up correctly. It's slightly more annoying to reverse engineer the OEM MAF transfer function but you already have the sensor wired up to the factory harness so keeping it around for a few weeks more while you figure out the tune is easy enough. I've seen GM also use a combination of both MAF + MAP in their ECUs before, MAF is for steady state and a calculation of the cylinder VE to correct the base VE table, then in transients it uses that calculated VE + raw MAP to determine cylinder filling somehow.
    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
×
×
  • Create New...