Jump to content
SAU Community

Recommended Posts

Just got the car back from a big-ish service incl all oils changed, fuel filters, gapped spark plugs etc and noticed that if I rev the engine and hold rpm somewhere between 1500 and 2500 rpm (I didn't try higher because I didn't want to attract attention to myself..) while the car is sitting idle in neutral, there's a muffled popping sound followed by a small shake (drive seat shakes noticably) every few seconds ..sometimes more than one in a row.

Like popcorn starting to pop ..just more muffled sound, and each pop shakes the car a bit. Is this just the exhaust note or should I be worried ? Detonation? Car's ecu was tuned before the service and it was NOT pinging/detonating...

The car's an R34 GTT with a turbo-back exhaust with a 3" catback (HKS SilentPower)

I never noticed this before but then again I never held the engine at 1500rpm for a few seconds before either..

Link to comment
https://www.sau.com.au/forums/topic/231130-popping-sound-and-car-shaking/
Share on other sites

hm are you sure this is missfire? I searched for "Popping" last night and read a lot of older discussions and a lot of people seem to be under the impression that these popping sounds are normal on skylines and a few said it's probably due to running rich in that rev range .. no mentions of missfire anywhere.

I have no idea which plugs they put in ... I'm taking the car back to unigroup to have a listen to this. Could it be due to old fuel? car's been at the shop for was 2 weeks and only 1/4 of tank of fuel sitting in it

Edited by Delta Force

mine runs rough in the same situation. though in mine i put it down to section of the map thats never been tuned.

It's just a rich miss and nothing to be overly concerned about. It's something tune related and i wouldn't expect it's a result of a service. I'm pretty sure unigroup will tell you the same thing but it doesn't hurt to have it looked at if you are concerned.

Took it back to unigroup and as soon as Yavuz heard the popping at idle and low revs he said "yep it's misfiring" .. and that it's due to the small gap (0.75mm) so they regapped the spark plugs to 1mm and no more misfire/popping sounds ;-) Best of all ..they did it all for free! That's good service. Cheers.

Took it back to unigroup and as soon as Yavuz heard the popping at idle and low revs he said "yep it's misfiring" .. and that it's due to the small gap (0.75mm) so they regapped the spark plugs to 1mm and no more misfire/popping sounds ;-) Best of all ..they did it all for free! That's good service. Cheers.

Hey mate was yours the black r34 there? I was there about a week ago also.. had a safc tune. Mine is doing the same thing and yavuz said its normal with running small gapped plugs.. Funny i also hear it pop every now and then only on idle

just one thing ... Yav also mentioned that the car may misfire at higher rpms with bigger gap (and non stock boost). But for me that's not really an issue as a very rarely go above 4000rpm anyway (daily driver)

  • 3 years later...

sorry to bring up an old thread but i think my input is relevant and not worth starting a new thread.......

i have been experiencing the same muffled popping/rumble sound then shaking when car is idling after cold start. i noticed the rumble and shaking start to settle down after the engine oil had warmed up to about 90 degrees.

couldn't figure out what was wrong, then 2 weeks later the check engine light came. it turned out an exhaust leak at the rear muffler was causing the rumble and shake while idling.

the leak was at the weld joints along the exhaust pipe that had started to rust. this was probably making the car run a little too rich as well, but i could be wrong.

cheers!!!

mine does it too at idle, is normal. atm mine has a dump pipe like 6 inches long and is running Super rich so it sounds worse, gaps are .8. is perfect when you apply any throttle though all the way to 7000rpm

mine does it too at idle, is not dangerous. atm mine has a dump pipe like 6 inches long and is running Super rich so it sounds worse, gaps are .8. is perfect when you apply any throttle though all the way to 7000rpm

ah crap that effort to edit a post was ABSOLUTE FAIL

Edited by PaulosECR33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Would you ever vent this bonnet or will it be unnecessary?
    • Happy new years folks! Wishing you all a successful year of money pit ownership!  So the subframe bushes are out....   Ok, who else has done that job before??  What a C U Next Tuesday of a job that is!  Be glad to not do that again in a hurry! I think I explored every option available to chop the middle section of the bushes out, most of them unsuccessfully! I dried a holesaw, die grinder, normal drill bit, air chisel, etc, etc. The true success happened by accident when I'd decided to try a step drill I spotted on the bench on the way passed.  See, there are benefits to never cleaning up after yourself! It RIPPED through so so much better than the drill bit. It has to be the skinniest one available so its small enough to fit between the inner tube and outer casing but it made easy work of it.  First one i hammered the shit out of... New method- 20250102_185506.mp4     I did the other 5 in less time than I fluffed around with the first one. I used the cut off saw (sawsall as the yanks love to call them) to cut a break in the casing. Even with that they're still a prick to hammer or air chisel out.  The last few i just went rambo with the air chisel without cutting them. I overcome one of the early ones so will hit the with the mig to fill the cut then sand it off smooth.  The carnage left over-   I've also been "nesting" ie, cleaning up my babies nursery,  ie cleaning the f**king pig sty of a shed. I've got that much shit laying around it's as cluttered as my head!  Getting things put away, in boxes, on shelves, hanging off walls, all to get some working space back again.  Hopefully that keeps me motivated....
    • AFAIK does the base map for Haltech even have the 4D compensation enabled? It's been a while but when I looked at it I remember it was actually using pure TPS as one load signal and MAP for another. Seemed workable but not ideal by any stretch. A lot of people have "make the event-itis" which leads to stuff like this happening.
    • https://www.youtube.com/watch?v=qHhWelSBppY
    • Even back in the day, some importers were renowned for bringing in crashed cars, giving them a quick touch up + respray and making them look mint
×
×
  • Create New...